Buchi Scrubber K-415 Operation Manual Download Page 47 | Manualshive

Page: 47 / 58

Buchi Scrubber K-415 Operation Manual Download Page 47

8 Troubleshooting

46

K-415 Operation Manual, Version B

7 .12 Silencer

Replace the silencer once a year.

7 .13 Functional test

A functional test to check whether the bypass valve functions properly and if the complete system of
the K-415 is tight can be performed by your service technician. Please contact your BUCHI service
center concerning this matter.

7 .14 Customer service

Only authorised service personnel are allowed to perform repair work on the instrument. These
persons have a comprehensive technical training and knowledge of possible dangers which might
arise from the instrument.
Addresses of official BUCHI customer service offices are given on the BUCHI website under:
www.buchi.com. If malfunctions occur on your instrument or you have technical questions or applica-
tion problems, contact one of these offices.

The customer service offers the following:
•  Spare part delivery
•  Repairs
•  Technical advice
•  Troubleshooting
•  Instrument qualification (IQ) and operative qualification (OQ)

«
...
45
46
47
48
49
...
»

Summary of Contents for Scrubber K-415



























































Reviews:

No comments