background image

IMPORTANT! KEEP FOR FUTURE REFERENCE

Failure to follow these warnings and the instructions could result in serious injury or death.

This unit must be assembled and disassembled by ADULTS ONLY.

This product is designed for children from 3-6 years old.

DO NOT exceed the maximum weight limit of 50 kg regardless of age.

Always provide the supervision necessary for continued safety of your children.

For domestic use only.

Check this product for damaged hardware, loose joints, missing parts, or shape

edges before assembly and periodically during use.

Swings and slides shall not be installed over concrete, asphalt or any other hard

surface.

DO NOT use this product in any manner other than its intended use.

DO NOT allow more than one child on the wavy slide and ladder at a time.

Children must ALWAYS remain securely seated, in the keep forward facing

position when sliding.

DO NOT lay down, slide from a standing position, or slide down the chute

back-wards.

DO NOT allow children to stand on the slide top.

DO NOT use in adverse weather conditions, while the seats are wet, or in poorly lit

conditions.

DO NOT move the product with child inside.

FALL HAZARD: Children have the risk of suffering injuries after falling from the

slide and swing. To prevent falls, parents should make the following measures:

Stay in arm’s reach of your children.

Always secure this product to support frame by connecting articles.

Changing areas are not designed for children playing.

CHOKING HAZARD: Keep medication and small items that could choke a child

away from the playhouse.

Summary of Contents for WM21B012












Reviews: