BTI 9097032, Original Instructions Manual

Page: 6 / 32

6
A14,4-18 LG-2
........................14,4 V, 18 V
...................................... 3 A
..................................500 mA
..................................704 g
...........................+5...+40 °C
ENGLISH
WARNING Read all safety warnings, instructions, illustrations and
speci fi cations provided with this power tool. Failure to follow all
instructions listed below may result in electric shock, fi re and/or serious
injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS
Do not dispose of used battery packs in the household refuse or by burning
them. BTI o ff er to retrieve old batteries to protect our environment; please
ask your sales representative or our service line at 07940 / 141-141.
Only the following battery packs can be
charged with this charger:
Battery Cat. No. Cell Type DC Volts Capacity Cell No.
A14,4V Li-Ion 14.4 ≤ 1.5 Ah 4
A14,4V Li-Ion 14.4 ≤ 3.0 Ah 2 x 4
A18V Li-Ion 18 ≤ 2.0 Ah 5
A18V Li-Ion 18 ≤ 5.0 Ah 2 x 5
A18V Li-Ion 18 ≤ 9.0 Ah 3 x 5
Do not try to charge non-rechargeable
batteries with this charger.
Do not store the battery pack together with metal objects (short circuit risk).
No metal parts must be allowed to enter the battery section of the charger
(short circuit risk).
Never break open battery packs or chargers and store only in dry rooms.
Keep dry at all times.
The battery clamps of the charger are fed by the mains supply. Do not touch
the tool with conducting objects.
Never charge a damaged battery pack. Replace by a new one.
Before use check machine, cable, and plug for any damages or material
fatigue. Repairs should only be carried out by authorised Service Agents.
This appliance is not intended to be used or
cleaned by persons with reduced physical,
sensory or mental capabilities, or lack of
experience or knowledge, unless they have
been given instructions concerning the safe
use of the appliance by a person legally
responsible for their safety. They should be
supervised whilst using the appliance.
Children shall not use, clean or play with this
appliance, which when not in use should be
secured out of their reach.
Warning! To reduce the risk of fi re, personal injury, and product damage due
to a short circuit, never immerse your tool, battery pack or charger in fl uid or
al-low a fl uid to fl ow inside them. Corrosive or conductive fl uids, such as
seawater, certain industrial chemicals, and bleach or bleach containing
products, etc., Can cause a short circuit.
SPECIFIED CONDITIONS OF USE
The quick charger can charge BTI Li-ion batteries from 14 V - 18 V.
Do not use this product in any other way as stated for normal use.
MAINS CONNECTION
Connect only to single-phase AC current and only to the system voltage
indicated on the rating plate. It is also possible to connect to sockets without
an earthing contact as the design conforms to safety class II.
CHARGING TIME
Battery Cat. No. Volts Capacity Charging Time
max.
A14,4V 14.4 V ≤ 1.5 Ah 40 min
A14,4V 14.4 V ≤ 3.0 Ah 75 min
A18V 18 V ≤ 2.0 Ah 40 min
A18V 18 V ≤ 5.0 Ah 75 min
A18V 18 V ≤ 9.0 Ah 191 min
LI-ION BATTERIES
The rechargeable batteries are partially charged. The LED on the battery
indicates the state of charge.
If it is not used for long periods, the rechargeable battery will switch to the
non-operative state.
When fully discharged the rechargeable battery switches o
ff automatically
(depth discharge not possible).
Under extreme circumstances, the internal temperature of the battery could
become too high. If this happens, the battery will shut down.
Place the battery on the charger to charge and reset it.
The state of charge can be read by pressing the button on the rechargeable
battery. The battery can be left in the electric tool while the reading is taken
but it must be switched o ff at least one minute beforehand (otherwise the
display will be inaccurate). The number of LEDs illuminated indicates the
state of charge. A fl ashing LED indicates a max. power reserve of 10%.
As a general principle, if the electric tool should fail to work after inserting the
rechargeable battery, then the battery should be plugged into the charger.
The displays on the battery and charger will then provide information about
the condition of the battery.
In low temperatures work may continue at reduced output.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods Legislation
requirements.
Transportation of those batteries has to be done in accordance with local,
national and international provisions and regulations.
• The user can transport the batteries by road without further
requirements.
• Commercial transport of Lithium-Ion batteries by third parties is
subject to Dangerous Goods regulations. Transport
preparation and transport are exclusively to be carried out by
appropriately trained persons and the process has to be
accompanied by corresponding experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and
insulated to prevent short circuit.
• Ensure that battery pack is secured against movement within
packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
TECHNICAL DATA BATTERY CHARGER
Voltage range ...................................................................................
Quick charge current ........................................................................
Maintaining charge current ..............................................................
Weight according EPTA-Procedure 01/2014 ...................................
Recommended ambient charging temperature ...............................
457 701 - BTI-A14-4-18LG-2.indd 6 457 701 - BTI-A14-4-18LG-2.indd 6 13.07.2020 10:26:58 13.07.2020 10:26:58