BST BS33 User Manual Download Page 11

 
   

 

  BS33 

 

Remarks: Due to our policy of continual product development, we reserve the right to amend the specifications of the mentioned 

products without notice

 

 

11 

10. SERVICE 

Warranty Conditions 
 
This meter is guaranteed against any material fault or manufacturer’s defect, in accordance 
with the general conditions of sale. During the warranty period (one year), faulty parts may be 
replaced,  with  the manufacturer  reserving  the  right  to  decide either  to  repair  or  replace  the 
product. 
 
In  the  event  of  returning  the  meter  to  the  after-sales  service  or  to  a  regional  branch,  the 
outward transport is payable by the customer. The delivery must be agreed in advance with 
consignee. 
 
For  delivery  indicate,  by  means  of  an  enclosed  note,  as  clear  as  possible,  the  reasons  for 
returning it. Use only the original packing. 
 
Any  damage  caused by  shipment using  NOT the  original  packaging  will  be  charged  in any 
case to the consignor. 
 
The manufacturer will not be responsible for any damage to persons or things. 
 
The warranty does not apply to the following cases: 

• 

Accessories and battery are not included in warranty. 

• 

Repairs  following  unsuitable  use  of  the  meter  or  by  combining  the  latter  with 
incompatible meter or accessories. 

• 

Repairs resulting from incorrect shipping. 

• 

Repairs  resulting  from  servicing  carried  out  by  a  person  not  approved  by  the 
company. 

• 

Modifications  to  the  meter  without  explicit  authorisation  from  our  technical 
department. 

• 

Adaptation  to  a  particular  application  not  provided  for  by  the  definition  of  the 
meter or by the instruction manual. 

 
The  contents  of  this  manual  may  not  be  reproduced  in  any  form  whatsoever  without  the 
manufacturer’s authorisation. 
 
Our  products  are  patented.  The  logotypes  are  registered.  We  reserve  the  right  to 
modify  specifications  and  prices  as  part of  technological  developments which  might 
be necessary

Summary of Contents for BS33













Reviews: