background image

3 0

Input being edited

Current Parameter

Frequency

Cursor

If the FDS-355 is configured for MONO, all EQ’s will be mono. If configured

for 2x2+1 ("stereo"), EQ’s will be marked as Stereo 'S' when STEREO LINK is

ON, and the stereo marker will show an 'S' next to the EQ number.
Available spare EQ filters are also shown above the graphic area.

Adding a new EQ:

If you press the UP key and the screen does not change, then you have

reached the last EQ currently in use. To add an EQ, the cut/boost of the

highest EQ must be edited. Another EQ (assuming there are spare EQs) will

then be inserted automatically. A dotted contour shows the effect of the

crossover filters on this band.

NOTE: The A+B signal is mixed after the EQ sections on A and B, so the A+B

signal is affected by A and B EQ.

EQ shape

The shape of the EQ can be selected from one of the following by turning the

parameter wheel:
Hi shelving with 12dB slope (Hi12)

Hi shelving with 6dB slope (Hi6)

BELL

Low shelving with 6dB slope (Lo6)

Low shelving with 12dB slope (Lo12).

The EQ shape icon at the top of the screen will change, to show the type of

EQ selected.

EQ menu

Current Parameter

selection

10.0

EQ Screens

Unused EQs

Cut/boost

Width

Stereo

marker

Summary of Contents for FDS 355





















































Reviews: