background image

PAGE 12

  Your SENSORFLO® Faucet is designed and engineered in accordance with the highest quality and performance standards. With 

proper care, it will provide years of hygienic and trouble-free service.

  Periodically, the Faucet will require some minor maintenance to keep it at peak performance. There are 2 low battery indicator 

lights. One located on the Sensor on the Faucet body and the other located on the Solenoid Box. When the low battery light on the 

Sensor blinks, it indicates that the battery is low. However, the Solenoid can still function at this point. When the low battery light on 

the Solenoid blinks, the Solenoid will stop functioning at this point and the batteries need to be replaced immediately. To replace 

the batteries, follow the installation instructions in the electrical connections section of this document. 

  Periodically clean the In-Line Filter.

  The polished chrome finish of your Faucet should be cleaned using mild soap and warm water.

  Dry immediately with a soft, clean cloth for best results.

  NEVER use abrasive cleaners, chemicals, alcohol or other solvents. They may damage the surfaces of the non-chrome plated finishes.  

CARE & CLEANING

WAIVER & DISCLAIMER

This waiver-disclaimer is attached to and made a part of the written contract to purchase these products for use in psychiatric and correctional 
facilities. Such fixtures and products are purchased to reduce the risk of self-imposed death or injury to patients or clients in such facilities, but are 
NOT represented as able to prevent such death or injury.

Behavioral Safety Products, LLC (“BSP”) as the seller and Speakman Company as the manufacturer of these products have not, and will not 
represent or warrant to the purchaser shown in this contract (“Purchaser”) that its fixtures and products will prevent death or injury in any case 
whatsoever.

BSP and Speakman Company make no express or implied warranty with respect to the preventative quality of its products, but merely represent 
that the use of such products tends to reduce deaths and injuries by patients or clients who are subject to meticulous screening processes and 
diligent supervision on the part of the facility housing them.

Purchaser acknowledges the foregoing disclaimer and waives any and all claims against BSP and Speakman Company as to express or implied 
warranties of fitness for any purpose whatsoever.

IMPORTANT

  This fixture must be mounted with its back to a wall.

  It is unsafe if the unit could be accessed from the back side.

  All plumbing and electrical connections under the sink are not ligature resistant and should be in a separate enclosure or cabinet 

(not supplied).

706-705-1500                                                    

besafepro.com

CONTINUED

Summary of Contents for SF390















Reviews: