background image

English

14

7 TORQUE LIMITING DEVICE (AQ25 / 30 / 50 only) 

The actuator is protected by a torque limiting device in case of over-

torque. 

If the actuator stops in a position which is not the one

 

desired, please check if actuator did not reach

mechanical stops or that valve has no stiff point.

Actuators are set and tested in factory according to torque stated on 
orders. If no torque is specified, the actuator is supplied with 

limiter set to the maximum output torque. In both of these 

cases, you can adjust torque limiter if necessary. 

Torque limiter operation

Please check below torque limiter setting components.

5

 – Clockwise direction 

cam

4

 – Clockwise direction 

switch

3

 – Counter-clockwise 

direction cam

2

 – Counter-clockwise 

direction switch

1

 – Torque scale disk

Torque limiter is triggered as (

3

) and (

5

) cams trigger their

corresponding (

2

) and (

4

) switches when rotating.

Torque scale disk (

1

) allows to set torque limit for both directions.

It has torque graduations from 40 to 100% of the maximum

torque deliverable by the actuator. 

To adjust torque, set the tip of cam to match the torque 
percentage desired on the disk. 

Torque scale disk is factory-set and is a reference for cams setting.

 

Do not modify its position or you will not be able to set the
torque limiter accurately.

  

15

Summary of Contents for 215.3842.6.11 171.8093.1L.13
















Reviews: