Bryston PowerPac 120 Owner'S Manual Download Page 9

BRYSTON 20 -YEAR WARRANTY

Bryston products are warranted to be free 
from manufacturing defects for a minimum 
of twenty years from the original date of
manufacture. This includes parts, labour
and return shipping to the first owner and
all subsequent owners. Warranty coverage 
is automatic and commences with the
original date of manufacture which is kept
on file at Bryston.

In the event of a defect or malfunction,
Bryston will remedy the problem by repair
or replacement, as we deem necessary, to 
restore the product to full performance.

This warranty is considered void if the
defect, malfunction or failure of the
product or any component part was
caused by damage (not resulting from a
defect or malfunction) or abuse while in
the possession of the customer, tampering 
by persons other than factory-authorized
service personnel, or failure to comply
with Bryston operating instructions.

This warranty gives you specific legal
rights and you may also have other rights
which may vary from province to province 
and country to country.

 

BRYSTON SERVICE USA.: 

BRYSTON SERVICE OUTSIDE CANADA & the USA:

 70 COVENTRY ST. SUITE #5 

CONTACT YOUR LOCAL DISTRIBUTOR

 

NEWPORT VERMONT 

OR

 

U.S.A. 05855 

CHECK OUR WEB SITE AT: [email protected]

 

 

E-MAIL BRYSTON DIRECTLY: [email protected]

 

PHONE: 802-334-1201 

FAX BRYSTON DIRECTLY: 705-742-0882

 

FAX: 802-334-6658 

PHONE BRYSTON DIRECTLY: 705-742-5325

 E-MAIL: [email protected]

BRYSTON LTD., 677 NEAL DRIVE, P.O. BOX 2170, PETERBOROUGH, ONTARIO CANADA  K9J 7Y4

Summary of Contents for PowerPac 120













Reviews: