code: YYWW where YY is the 2 least significant digits of the year and WW is the
week of the year from 01 to 52) .
4.
EXTERNAL TURN-ON (REMOTE/LOCAL)
REMOTE:
To power-up the 9B
SST
2
using an external control voltage, supply a 4v to
12v AC or DC control voltage to the ‘IN’ terminals of the
External Turn-On
connec-
tor ( 5 ) . Use insulated 18-22 gauge stranded wire between the source device and
the 9B
SST
2
.
Immediately following power up, the control voltage will appear at the ’OUT’ termi-
nals of connector (5) for the control of other equipment . The removal of the control
voltage causes the 9B
SST
2
to turn off and the control voltage at the ‘OUT’ terminals
is interrupted . The 9B
SST
2
draws less than 2mA of current from this control signal .
LOCAL:
in this position the 9B
SST
2
will ignore the control voltage and power up
only by using the front panel power switch .
N.B.
The Power Switch/Circuit Breaker on the power entry panel at the rear of the
9B
SST
2
must be ON for the unit to operate .
5.
EXTERNAL TURN-ON CONNECTOR
A 4 terminal connector (plug) with screw tightened bare
wire cage-clamps is provided with each 9B
SST
2
. This
connector is in turn plugged into the 4 pin header in the
9B
SST2
to facilitate easier hookup and or removal of a
remote control power on/off signal . Replacement or
additional plugs are available from Bryston .
(Part no . CO110A11104)
D
AT
A
PL
AT
E
M
od
el
n
am
e
&
re
vi
si
on
,
Se
ria
l n
um
be
r,
D
at
e
co
de
,
El
ec
tri
ca
l r
at
in
g,
e
tc
.
EXTERNAL TURN-ON
4~
12
V
AC
/D
C
O
U
T
IN
LOCAL
REMOTE
POWER SWITCH/CIRCUIT BREAKER
BR
YS
TO
N
LT
D.
P
ET
ER
BO
RO
UG
H,
O
NT
AR
IO
, C
AN
AD
A
O
N
4
5
3
2
1
MORE INFORMATION
More information about the 9B
SST
2
, including schematic drawings and other technical information, is available at www .
bryston .com . For example:
BRIDGING CHANNELS:
For information on bridging 9B channels refer to the document "6B-9B-BRIDGED-HOOKUP .pdf" which can be found on
www .bryston .com in TECHNICAL INFORMATION
SST2 Amps
9B
SST
2
MEMOs
RACK MOUNTING INSTRUCTIONS:
For further information on rack mounting the 9B
SST
2
refer to the document "9BSST_RACK_MOUNTING_INSTRUC-
TION_SHEET .pdf" which can be found on www .bryston .com in the TECHNICAL INFORMATION section .
POWER OUTPUT:
120 watts per channel into 8 ohms
200 watts per channel into 4 ohms
GAIN / SENSITIVITY:
29dB (1 .1Vin = 120W @ 8 Ohms)
23dB (2 .2Vin = 120W @ 8 Ohms)
17dB (4 .4Vin = 120W @ 8 Ohms )
INPUT IMPEDANCE:
30K ohms (±5%) single ended
20K ohms (±5%) balanced (each leg)
DISTORTION:
< 0 .005% 20Hz to 20kHz at 120 watts into 8 ohms,
IMD & THD+NOISE:
< 0 .007% 20Hz to 20kHz at 200 watts into 4 ohms
NOISE:
Measured with input shorted (20Hz to 20kHz .)
>110dB below rated output 29dB gain (- 73dBu)
>113dB below rated output 23dB gain (- 76dBu)
>116dB below rated output 17dB gain (- 79dBu)
SLEW RATE:
>60 volts per microsecond
POWER BANDWIDTH
: <1 Hz to over 100 kHz
DAMPING FACTOR:
Over 500 at 20 Hz, ref . 8 ohms
DIMENSIONS:
19" Rack mount version: 48 .3 x 13 .3 x 48 .5cm
(19"w x 5 .25"h x 19 .1"d) with handles
17” version w/o handles: 43 .2 x 13 .3 x 44 .4cm
(17"w x 5 .25"h x 17 .5"d)
SHIPPING WEIGHT:
approx . 34 .5kg (76 lbs)
POWER CONSUMPTION
& HEAT LOAD:
single channel 120W @ 8 ohms: 242 Watts
5 channels @ 120W @ 8 ohms: 1397 Watts
Max . Heat Dissipation 8 ohms: 2720 Btu/Hr .
single channel 200W @ 4 ohms: 422 Watts
5 channels @ 200W @ 4 ohms: 2295 Watts
TECHNICAL SPECIFICATIONS
9B
SST2
POWER ENTRY PANEL
Summary of Contents for 9B?SST2
Page 1: ...OWNER S MANUAL 9BSST2 ...
