
8
1. Input Select Switch:
Select either Balanced or Single Ended audio
input.
2. Balanced Audio Input:
This input connector accepts standard XLR (pin
1 = Ground, pin 2 = Positive, pin 3 = Negative) or
1/4” Phone plugs (sleeve = Ground, tip = Positive,
ring = Negative). Use quality, 100% shielded
cables with gold plated connectors.
3. Single Ended Audio Input:
This input connector accepts standard ‘RCA’ or
‘Phono’ connectors. Use quality, 100% shielded
cables with gold plated connectors.
4. Gain Select Switch:
The optimum gain setting will depend upon the
source pre-amp operating level, and or personal
preference.
The 29dB setting is used when the source is
single-ended or from a transformer coupled
balanced source. This is the typical for single
ended or un-balanced operation. The 29dB
setting provides the most amplifier gain and
equates to 100w @ 8 ohms output for a 1V input
(noise -115 dB).
The 23dB setting is used when the source
output is actively balanced. This is the typical
setting for balanced operation. Or use this
setting whenver less gain is required. The 23dB
setting equates to an output of 100w @ 8 ohms
for 2V input (noise -119 dB).
The noise is referenced in dB below rated
output. Different input configurations result
in slightly different noise readings. The above
noise ratings represent minimum readings.
Actual readings may be better.
5. Channel Level Attenuator (PRO
ONLY):
The level control will attenuate the input signal
level from 0dB through -14dB.
Rear Panel
WARNING
DO NOT CONNECT ANY
TERMINALS TOGETHER OR
TO GROUND.
RISK OF HAZARDOUS
ENERGY. MAKE PROPER
SPEAKER CONNECTIONS.
USE CLASS 2 WIRING.
AVERTISSEMENT
NE PAS BRANCHER LES
BORNES ENSEMBLE OU À LA
TERRE. RISQUE DE ÉNERGIE
DANGEREUSE. FAIRE
CONNECTIONS ENCEINTE
ADÉQUAT. UTILISATION
CÂBLAGE DE CLASSE 2.
WARNING
DO NOT CONNECT ANY
TERMINALS TOGETHER OR
TO GROUND.
RISK OF HAZARDOUS
ENERGY. MAKE PROPER
SPEAKER CONNECTIONS.
USE CLASS 2 WIRING.
AVERTISSEMENT
NE PAS BRANCHER LES
BORNES ENSEMBLE OU À LA
TERRE. RISQUE DE ÉNERGIE
DANGEREUSE. FAIRE
CONNECTIONS ENCEINTE
ADÉQUAT. UTILISATION
CÂBLAGE DE CLASSE 2.
PRO
REG
CAN ICES-3 (B)/NMB-3(B)
_
+
3 G
2
1
+
_
G
This device complies with part 15 of
the FCC Rules. See manual for details.
23dB
GAIN
SINGLE
ENDED
SINGLE
ENDED
SINGLE
ENDED
BALANCED
INPUTS
CAUTION
ATTENTION
RISK OF ELECTRIC SHOCK - DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR
STATUS
STATUS
See operating manual
for further details.
LOCAL
EXTERNAL
IN
OUT
12V
POWER UP
600W/8
Ω
600W/8
Ω
CH1 OUTPUT
CH1 OUTPUT
600W/8
Ω
600W/8
Ω
CH
CH
2
2
OUTPUT
OUTPUT
BALANCED
29dB
O
N
FF
O
o
I
O
N
FF
O
o
I
PUSH
1
2
3
PUSH
1
2
3
PUSH
1
2
3
PUSH
1
2
3
14B3-Cubed Rear Panel Rev 1
July 7 2015
Garry Faulds
14.00"
made in/fabrique au
Peterborough, Ontario, Canada
3
CIRCUIT BREAKER
POWER SWITCH
CIRCUIT BREAKER
POWER SWITCH
IEC320 POWER INLET
+
G
2
+
G
-
1
3
¼” PHONE or 3-Pin XLR
+
G
2
+
G
-
1
3
¼” PHONE or 3-Pin XLR
BALANCED INPUTS
CAUTION
RISK OF ELECTRIC SHOCK - DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
ATTENTION
Ch2
Ch1
GAIN
23dB
29dB
INPUT
BALANCED
SINGLE ENDED
SINGLE
ENDED
INPUT
SINGLE
ENDED
INPUT
-14
0dB
LEVEL
See operating manual
for further details.
LOCAL
EXTERNAL
IN
OUT
12V
POWER-UP
-14
0dB
LEVEL
1
2
3
11
4
5
6
7
8
9
10