Bryston 14B3 Owner'S Manual Download Page 7

14B

3

 Amplifier

7

1. Power/Standby Switch:

The front panel features a push-on/push-off 

type latching power switch used to apply or 

remove A/C line power to the SoftStart circuitry. 

Note that the rear circuit breaker must be on for 

the amplifier to power-up.

2. LED Indicator: 

Each amplifier channel has a front panel LED 

indicator to monitor the following conditions:

Unlit

Amplifier not powered on (OFF 

MODE)

Red

Channel is muted during power up

Green

Channel operation is normal

Flashing 

Red

Channel is clipping. Reduce input 

level!

Orange

Thermal protection mode

POWER UP SEQUENCE

 

After pushing the power switch, each channel 

LED will turn from unlit to red (mute). When the 

power supplies have stabilized, the channel will 

come out of mute and the LED will change to 

green (normal operation).

UNLIT LED

  (No power)

 

The amplifier channel LED when unlit indicates 

no A/C mains power is present at the channel 

power transformer. This usually indicates 

that the amplifier probably needs only to be 

powered on.

CLIPPING

 (flashing red)

 

Clipping occurs when the channel output level 

no longer can follow the level increase at the 

input (over driven input condition). When a 

channel is driven into clipping, the channel 

LED will change from green to red then back to 

green when the level is reduced. Momentary 

clipping can be tolerated, however it indicates 

that maximum undistorted power has been 

surpassed and potential speaker damage 

may result if overload conditions persist. Any 

amplifier that is constantly operated into 

clipping indicates a more powerful amplifier is 

needed for that application.

THERMAL SHUTDOWN

 (orange)

 

Each channel has thermal shutdown circuitry 

to prevent damage due to overheating.  Should 

thermal shutdown occur, the channel will mute, 

and the channel LED will turn orange. When 

the channel has cooled to a safe operating 

condition, the channel will return to normal 

operation. Persistent thermal shutdown 

indicates steps need to be taken to increase 

airflow across the channel or channels heat 

sink. See “Ventilation” on page 4.

In some markets the LED indicators, which are  

normally red/green, may be red/blue instead. 

When red/blue LEDs are supplied green is 

replaced with blue and orange is replaced with 

magenta in the above descriptions.

Front Panel

17.00"

7.50"

19”

19.00”

1

2

Summary of Contents for 14B3













Reviews: