manualshive.com logo in svg

Bryant CONDENSING GAS FURNACE 355MAV, Installation, Start-Up, And Operating Instructions Manual

The Bryant CONDENSING GAS FURNACE 355MAV provides optimal heating performance for your home. To ensure a seamless installation and operation, make sure to download the Installation, Start-Up, And Operating Instructions Manual for free from our website. Get all the necessary guidance and enjoy hassle-free use of your furnace.

Share
Download
background image

NOTE:

Read the entire instruction manual before starting the

installation.

This symbol

→

indicates a change since the last issue.

Index

Page

SAFETY CONSIDERATIONS .....................................................2
DIMENSIONAL DRAWING........................................................3

Clearances to Combustibles......................................................4

CODES AND STANDARDS........................................................5
ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS........5
INTRODUCTION ..........................................................................6
APPLICATIONS............................................................................6

General ......................................................................................6
Upflow Applications.................................................................6
Downflow Applications ............................................................8
Horizontal Left (Supply-Air Discharge) Applications ..........10
Horizontal Right (Supply-Air Discharge) Applications ........12

LOCATION..................................................................................13

General ....................................................................................13
Low-Heat Only Installation ....................................................14
Furnace Location Relative to Cooling Equipment ................15
Hazardous Locations...............................................................15

INSTALLATION .........................................................................15

Leveling Legs (If Desired) .....................................................15
Installation In Upflow or Downflow Applications................15
Installation In Horizontal Applications ..................................17
Air Ducts.................................................................................18

General Requirements .......................................................18
Ductwork Acoustical Treatment .......................................18
Supply Air Connections ....................................................18
Return Air Connections.....................................................18

Filter Arrangement..................................................................18
Bottom Closure Panel.............................................................19
Gas Piping...............................................................................19
Electrical Connections ............................................................20

115-v Wiring......................................................................20
24-v Wiring........................................................................22
Accessories ........................................................................22

Direct Venting.........................................................................22

Removal of Existing Furnaces from

Common Vent Systems................................................22

Combustion-Air and Vent Piping .....................................25
Concentric Vent and Combustion-Air Termination

Kit Installation..............................................................31

Multiventing and Vent Terminations................................34

Condensate Drain....................................................................34

General...............................................................................34
Application.........................................................................34
Condensate Drain Protection.............................................35

START-UP, ADJUSTMENTS AND SAFETY CHECK......35

General...............................................................................35
Select Setup Switch Positions...........................................36
Prime Condensate Trap With Water.................................37
Purge Gas Lines ................................................................37
Sequence of Operation ......................................................37

Single-Stage Thermostat and Two-Stage Heating
(Adaptive Mode) ..........................................................37
Two-Stage Thermostat and Two-Stage Heating .........39
Cooling Mode...............................................................39
Thermidistat Mode .......................................................40
Super-Dehumidify Mode..............................................40
Continuous Blower Mode ............................................40
Heat Pump ....................................................................41
Component Test ...........................................................41

Adjustments .......................................................................41

Set Gas Input Rate .......................................................41
Set Temperature Rise...................................................48
Set Thermostat Heat Anticipator .................................49

A93040

ama

CERTIFIED

®

REGISTERED

ISO 9001:2000

As an ENERGY STAR®
Partner, Bryant Heating &
Cooling Systems has de-
termined that this product
meets

the

ENERGY

STAR® guidelines for en-
ergy efficiency.

Fig. 1—Multipoise Orientations

A93041

UPFLOW

DOWNFLOW

HORIZONTAL

LEFT

AIRFLOW

AIRFLOW

AIRFLOW

AIRFLOW

HORIZONTAL

RIGHT

installation, start-up,
and operating instructions

DELUXE 4-WAY MULTIPOISE
VARIABLE-CAPACITY DIRECT-VENT
CONDENSING GAS FURNACE

Cancels:

II 355M-40-13

II 355M-40-14

3-05

355MAV

Series I

—1—

Summary of Contents for CONDENSING GAS FURNACE 355MAV





















































Reviews:

No comments

Related manuals for CONDENSING GAS FURNACE 355MAV

ICP 445 02 4054 01 Installation Instructions And Use & Care Manual preview
445 02 4054 01
Brand: ICP Pages: 33
York TM9M Installation Manual preview
TM9M
Brand: York Pages: 44
Trane ADD2B060A9V3VA Installer'S Manual preview
ADD2B060A9V3VA
Brand: Trane Pages: 24
Lennox G24E SERIES User'S Information Manual preview
G24E SERIES
Brand: Lennox Pages: 4
Allied 80G1DFE Service Manual preview
80G1DFE
Brand: Allied Pages: 33
Allied 80G2UH070AV12 Installation Instructions Manual preview
80G2UH070AV12
Brand: Allied Pages: 39
Allied 80G2UH-V Installation Instructions Manual preview
80G2UH-V
Brand: Allied Pages: 44
Allied 92G1DFE Installation Instructions Manual preview
92G1DFE
Brand: Allied Pages: 48
Walter Wilson OLR112A16A Installation Instructions And Homeowner'S Manual preview
OLR112A16A
Brand: Walter Wilson Pages: 48
York P*XU/G9D-UP Installation Instruction preview
P*XU/G9D-UP
Brand: York Pages: 32
Unitary products group DLAS Installation Instructions Manual preview
DLAS
Brand: Unitary products group Pages: 24
Bard WG241 Installation Instructions Manual preview
WG241
Brand: Bard Pages: 73
Barnstead FB1310M Operation And Repair Manual And Parts List preview
FB1310M
Brand: Barnstead Pages: 32
Revolv RE9X-10N4 Owner'S Manual And Installation Instructions preview
RE9X-10N4
Brand: Revolv Pages: 24
vita vacumat 4000 premium t Operating Manual preview
vacumat 4000 premium t
Brand: vita Pages: 31
Thermo Pride OH16-125 Operation Manual preview
OH16-125
Brand: Thermo Pride Pages: 18
Thermo Pride OH5-85DXE Installation And Operation Manual preview
OH5-85DXE
Brand: Thermo Pride Pages: 17
Thermo Pride OD6FA072D48 Installation, Operation And Service Manual preview
OD6FA072D48
Brand: Thermo Pride Pages: 43

Brands by name

Popular brands

Load more brands