background image

7

A00227

Fig. 16 -- Slide Side Filter Out of Furnace

A00228

Fig. 17 -- Slide Bottom Filter Out of Furnace

4. Inspect the filter. If torn, replace it.

NOTE

: If a washable filter has been replaced with:

a. Factory specified disposable media filter — Do not

clean. If dirty, replace only with media filter having the
same part number and size. Install with airflow direction

arrow pointing towards blower.

b. Electronic Air Cleaner (EAC) — Refer to EAC

Owner’s Manual for maintenance information.

5. Wash filter (if dirty) in sink, bathtub, or outside with a

garden hose. Always use cold tap water. A mild liquid de-

tergent may be used if necessary. Spray water through filter
in the opposite direction of airflow. Allow filter to dry.

6. Reinstall clean air filter.
7. Replace filter cabinet door. (See Fig. 18 and 19.)
8. Turn on electrical supply to furnace (See Fig. 11).

A06192

Fig. 18 -- Replace Side Filter Cabinet Door

A06193

Fig. 19 -- Replace Bottom Filter Cabinet Door

NOTE

: If side return ducts are used, 2 filters may be required in

some models. The procedure listed above may be used to remove
side filters.

PERSONAL INJURY HAZARD

Failure to follow this caution may result in personal injury.
Use care when cutting support rods in filters to protect against

flying pieces and sharp rod ends. Wear safety glasses, gloves,

and appropriate protective clothing.

CAUTION

!

Filters may be field modified by cutting filter material and support

rods (3) in filters. Alternate sizes and additional filters may be

ordered from your dealer.

FURNACE CASING WIDTH

IN (MM)

FILTER QUANTITY AND SIZE *

**

FILTER TYPE*

SIDE RETURN

IN (MM)

BOTTOM RETURN

IN (MM)

14---1/2 (368)

(1) 16 x 25

(406 x 635)

(1) 14 x 25

(356 x 635)

3/4” (19 mm) thick washable or

4---5/16” (110 mm) thick

media---type

17---1/2 (445)

(1) 16 x 25

(406 x 635)

(1) 16 x 25

(406 x 635)

3/4” (19 mm) thick washable or

4---5/16” (110 mm) thick

media---type

21 (533 )

(1) 16 x 25

(406 x 635)

(1) 20 x 25

(508 x 635)

3/4” (19 mm) thick washable

or 4---5/16” (100 mm) thick

media---type

24 (610)

(1) 16 x 25

(406 x 635)

(1) 24 x 25

(610 x 635)

3/4” (19 mm) thick washable or

4---5/16” (100 mm) thick

media---type

*Recommended

**Some furnaces may have 2 filters

Summary of Contents for 311JAV Legacy Line Plus 80











Reviews: