background image

3-10

Section 3

Fuel Systems

Static Electricity

A discharge of static electricity can ignite gasoline

vapor that has accumulated during the fueling pro-

cess.  Use extreme caution when fueling your boat

under unusual circumstances such as when the boat

is suspended in a boatlift.

Your boat has important safety features and systems

that can be defeated by not following standard fueling

practices.  Under normal conditions, your boat’s bond-

ing system protects it from accumulating and discharg-

ing static electricity.    

Here are some important guidelines to protect you

from static electricity discharge while fueling:

• Always keep your boat in continuous contact with

the water or a land-based grounding system dur-

ing fueling.

• Always keep the fuel nozzle in contact with the

fuel fill assembly or the edge of the fuel tank

opening during the fueling process.  This contact

must be continuously maintained until fuel flow

has stopped.

• Never fuel your boat under unsafe conditions that

could increase the possibility of creating static

electricity.

• Only fill portable gasoline tanks while on land,

never on-board the boat.

• Never use homemade containers as a source of

gasoline to fill your fuel tank.

• Only carry gasoline on-board in a UL-approved

container or in a portable gasoline tank such as

those provided with outboard engines.  

• Never store portable gasoline tanks in living,

engine, or mechanical spaces.

Summary of Contents for Boston Whaler 22 Guardian Series

































































































































Reviews: