Bruker 004-130-000 Manual Download Page 36 | Manualshive

Page: 36 / 68

background image

Abbreviated Instructions for the MultiMode AFM

32

Scanning Probe Microscope Training Notebook

Rev. F

15.0 Abbreviated Instructions for the MultiMode AFM

15.1 Mode of Operation

In the

Other Controls

panel, set

AFM Mode

to Tapping, Contact, or choose the appropriate

profile and change the mode switch on the base to

TMAFM

or

AFM

&

LFM

mode, respectively.

15.2 Mount

Probe

1. Mount a probe into the cantilever holder. Be sure that it is in firm contact with the end of the

groove.

•

Tapping: Use an etched single crystal silicon probe (TESP).

•

Contact: Use a silicon nitride probe (NP).

2. Put the cantilever holder in the optical head. Secure the holder by tightening the screw in the

back of the optical head.

15.3 Select

Scanner

Choose a scanner (A, E, or J). Mount and plug the scanner into the base. Attach the corresponding
springs to the microscope base. In the software, choose the appropriate scanner parameters with

Microscope

>

Select

.

15.4 Mount

Sample

Mount a sample on a metal disk with a “sticky-tab” (sample width should be limited to the disk’s
15mm diameter). Mount the disk and sample on top of the scanner.

15.5 Place Optical Head on Scanner

1. Raise all three coarse-adjust screws on the scanner so that there is enough clearance between

the tip and sample when the optical head is placed on the scanner. If using a JV or EV
scanner, you only need to raise the motor screws.

2. Place the optical head on the scanner, still checking that the tip doesn’t touch the sample.

Attach the springs to the optical head.

3. Plug in the connector from the optical head to the base.

4. Bring the tip close to the sample keeping the head level by lowering all three coarse-adjust

screws.

«
...
34
35
36
37
38
...
»

Summary of Contents for 004-130-000





































































Reviews:

No comments

Related manuals for 004-130-000

Brand: IBM Pages: 208

Brand: IBM Pages: 2

SIERRA WIRELESS 250U 4G/3G LAPTOP CARD

Brand: Time Warner Cable Pages: 5

Brand: Fujitsu Pages: 116

Brand: Fujitsu Pages: 120

Brand: Fujitsu Pages: 165

Brand: Fujitsu Pages: 122

Brand: Fujitsu Pages: 112

Brand: Fujitsu Pages: 172

LifeBook E-6555

Brand: Fujitsu Pages: 108

Brand: Samsung Pages: 3

Brand: Samsung Pages: 4

Brand: Samsung Pages: 21

Brand: Samsung Pages: 16

Brand: Samsung Pages: 110

Brand: Samsung Pages: 103

Brand: Samsung Pages: 73

Brand: Samsung Pages: 110

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands