Brother RH-9800 Specifications Download Page 6

Page: 6 / 17

RH-9800 6/17

2002.10

Parts for the standard-sized fly indexer (Conventional parts)

Part name

Part code

Applicable specifications

Remarks

S42168-101

Without upper thread nipper

S42169-101

For L1, L2, L5

With upper thread nipper

S42110-101

Without upper thread nipper

Fly indexer assy

S42170-101

For L3, L4, L6, L7

With upper thread nipper

*If the standard-sized fly indexer is used for sewing with a non-standard distance between buttonholes and a non-standard number of

buttonholes (up to 9), you need to make additional holes in the cloth feed bar (F) assy (optional part). For this processing, refer to the
instruction manual supplied with this optional part.

Part name

Part code

Applicable specifications

Cloth feed bar (F) assy (L1, L2)

S45193-101

L1, L2, L5

Cloth feed bar (F) assy (L3, L4)

S45194-101

L3, L4, L6, L7

Parts for the large-sized fly indexer

Part name

Part code

Applicable specifications

Remarks

Fly indexer (LS) assy

S48329-101

L1, L2, L5

Fly indexer (LL) assy

S48334-101

L3, L4, L6, L7

Without upper thread nipper

*There are only four types of the distances between buttonholes for large

−

sized fly indexer.

Summary of Contents for RH-9800


















Search results

Summary of Contents for RH-9800

Reviews:

Related manuals for RH-9800

Brands by name

Popular brands

Brother RH-9800, Specifications

Search results

Summary of Contents for RH-9800

Reviews:

Related manuals for RH-9800

Brands by name

Popular brands