manualshive.com logo in svg

Brother HL-5580D, Service Manual

Share
Download
Brother HL-5580D Service Manual Download Page 55

2-29

Confidential

3.2.2 Touch panel models

Error message

Description

Error 

codes

Refer 

to:

First line

Second line

Cartridge Error

Put the Toner 
Cartridge back in.

The new toner sensor could not 
detect the new toner cartridge 
correctly.

4F01

2-50

Cooling Down

Wait for a while.

The side thermistor of the fuser 
unit or internal temperature sensor 
detected a temperature higher 
than the specified value.

6801

2-53

Cover is Open

-

The front cover sensor detected 
that the front cover was open.

6001

2-51

The eject sensor detected that the 
fuser cover was open.

6004

2-52

MX back cover sensor detected 
the open cover when the MX was 
selected as the output tray (before 
registering printing data to 
engine).

8808

2-74

MX back cover sensor detected 
the open cover when the MX was 
selected as the output tray (after 
registering printing data to 
engine).

8809

2-74

Drum !

-

Detected discharge that may be 
attributable to dirty corona wire on 
the drum unit.

6A00

2-54

Firmware Update You must update the 

firmware.

Firmware version of the main PCB 
is older than that of the TT, MX 
and LT.

9400

2-79

Ignore Data

Press Stop[x].

Detected undecodable data during 
printing. Received undecodable 
PS data.

---

4.11.1

Ignore Data

Jam 2-sided

-

The registration front sensor does 
not detect paper pass within the 
specified time after the first side 
was printed in duplex printing 
mode.

7800

2-66

Jam Inside

-

The eject sensor does not detect 
paper pass after the registration 
rear sensor detected the paper 
pass.

7000

2-55

Summary of Contents for HL-5580D


















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands