manualshive.com logo in svg

Brother HL-1060 Series, User Manual

Share
Download
Brother HL-1060 Series User Manual Download Page 86

USER’S GUIDE

APPENDIX A –6

RESIDENT FONTS

Bitmapped Fonts

This printer has the following bitmapped fonts. They can be used in the HP
LaserJet 5P, EPSON FX-850, and IBM Proprinter XL modes. They have
the following characteristics.

• 

Letter Gothic 16.66 Normal, Italic, Bold, BoldItalic (Portrait &
Lanscape)

• 

OCR-A(Portrait & Lanscape)

• 

OCR-B(Portrait & Lanscape)

Scalable Fonts

■

The following scalable fonts can be used in the HP LaserJet 5P,
EPSON FX-850, and IBM Proprinter XL modes.

Intellifont Compatible Fonts

• 

Alaska (Extrabold)

• 

Antique Oakland (Oblique, Bold)

• 

Brougham (Oblique, Bold, BoldOblique)

• 

Cleveland Condensed

• 

Connecticut

• 

Guatemala Antique (Italic, Bold, BoldItalic)

• 

Letter Gothic (Oblique, Bold)

• 

Maryland

• 

Oklahoma (Oblique, Bold, BoldOblique)

• 

PC Tennessee Roman (Italic, Bold, BoldItalic)

• 

PC Brussels Light (Italic, Demi, DemiItalic)

• 

Utah (Oblique, Bold, BoldOblique)

• 

Utah Condensed (Oblique, Bold, BoldOblique)

Microsoft Windows 3.1 TrueType Compatible Fonts

• 

BR Symbol

• 

Helsinki (Oblique, Bold, BoldOblique)

• 

Tennessee Roman (Italic, Bold, BoldItalic)

• 

W Dingbats

Summary of Contents for HL-1060 Series



























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands