Brother FAX-8360P Page 79 Owner'S Manual Download | Manualshive

Page: 79 / 126

background image

Troubleshooting and Maintenance

69

MAINTENANCE

DISCONNECTED

The other party or other party’s fax
machine terminated the call.

Try to re-transmit or call the other
party to see what happened.

MACHINE ERROR
XX

Machine has a mechanical problem.

Unplug the machine.

Then contact your Brother dealer
for service.

NO RESPONSE/BUSY

The number you called does not
answer or is busy. You may have
reached a number that is not
connected to a fax machine.

Check the number and try again.

NOT ASSIGNED

You tried to access a One Touch or
Speed Dial number that is not
programmed.

Set up the One Touch or Speed
Dial number. (See

Touch Dial Numbers

Storing Speed Dial Numbers

OUT OF MEMORY

The machine memory capacity has
been exceeded.

of Memory Message

PAPER JAM

The recording paper is jammed in the
machine.

PLS OPEN COVER

A page, piece of paper or paper clip,
etc. may be jammed inside the
machine.

Open the front cover and remove
the drum unit. If you see any
jammed paper or other item, gently
pull it out, then re-insert the drum
unit, close the front cover. If the
error message remains, open and
close the front cover again. If the
machine cannot reset itself and
return to the date and time prompt,
it will display

MACHINE

ERROR XX

. Please call your

Brother dealer for service.

TONER EMPTY

Toner is used up and printing is not
possible, or toner cartridge is not
installed into the drum unit.

Replace the toner cartridge with a
new one, or install the toner
cartridge into the drum unit. (See

Replacing the Toner Cartridge

ERROR MESSAGE

CAUSE

ACTION

«
...
77
78
79
80
81
...
»

Summary of Contents for FAX-8360P































































































































Reviews:

No comments

Related manuals for FAX-8360P

Brand: KANSAI SPECIAL Pages: 21

Brand: Jack Pages: 66

Brand: Jack Pages: 132

BOS-18 II 56382453

Brand: Clarke Pages: 28

Brand: MAGIC FX Pages: 20

Brand: Airtel Pages: 65

Brand: Janome Pages: 94

BARRACUDA 200ZW

Brand: Reliable Pages: 40

Brand: Baby Lock Pages: 226

Brand: Singer Pages: 27

Diversey ergodisc HD

Brand: Taski Pages: 81

Smoke 700 Magic

Brand: Audibax Pages: 2

Brand: Carina Pages: 30

Brand: Janome Pages: 43

Brand: Kärcher Pages: 5

Brand: JUKI Pages: 28

Brand: Siemens Pages: 104

Brand: 1byone Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands