Bronpi hydro series, Installation, Operating And Servicing Instruction

Page: 49 / 148

48
9.4.1 THERMO STOVE OR INSERT IGNITION
To ignite the thermo-stove or insert, press button no. 3 for a few seconds. The
display will show the ignition state as follows ( see drawing D76 ).
The maximum length of the ignition phase is 25 minutes. After this time, if there is
no visible flame, the thermo-stove will automatically go into an alarm state and the
control will show the message “Ignition Failure.”
9.4.2 THERMO STOVE OR INSERT IN OPERATION
Once the set smoke temperature has been reached, the thermo-stove or insert is
working. Before this, it will be in the state “Fire Present” and this will last just a few
minutes before considering the equipment totally ignited.
At that moment, the display will show the message “Work.” After this, our thermo-
stove or insert will be working normally ( see drawing D77 ).
The display shows the room temperature and the temperature reached by the circuit
water.
9.4.3 CHANGE OF THE SET-POINT ROOM TEMPERATURE
In order to modify the setting room temperature, please press button 4 and then
buttons 1 and 2 to increase or decrease it respectively ( see drawing D78 ).
If we want the thermo-stove or insert to be controlled by an external thermostat,
you should contact your Bronpi Calefacción S.L. authorised technical service
engineerbecause will be necessary to activate this external thermostat in the
technical menu. Connection of a volt free signal
from a room thermostat or heating controller to
the rear of the thermo-stove, and the correct
software parameters is all that is required ( see
drawing D79
). You can find Bronpi external
thermostat at the same Bronpi distributor where you bought your thermo-
stove.
Remember that if you want your thermo-stove or insert to start and stop
according to the demand of the external thermostat you must have the menu
“stand-by mode” activated (on). Otherwise, it will modulate when the water
temperature or external thermostat set-point
value is reached (the first one which reaches this
temperature).
9.4.4 CHANGE WATER TEMPERATURE SET
In order to modify the set water temperature, please press button 6 and then buttons
1 and 2 to increase or decrease it respectively ( see drawing D80 ).
9.4.5 ROOM OR WATER TEMPERATURE REACHES TEMPERATURE FIXED
BY THE USER
When the room temperature reaches the value set by the user or the water
temperature reaches the desired value, the thermo-stove or insert will automatically
operate at one lower power, it means that modulates in power. (
See drawing D81
).
Remember that if it is activated “stand-by mode”, when the ambient temperature
reaches the value set by the user plus a differential (2ºC) the thermo-stove or insert
MENU
D80
65º C
SET TEMPER
WATER
MENU
D81
16:40
27º C 63ºC
WORKING
MODULATE
MENU
0.0”
P-2
LOAD
TIME
POWER
OPERATIONAL
MENU
25.0º C
1.6 b
T-SCHEDA
PRES-H2O
WATER
PRESSURE
TEXT
MENU
10”
00”
RAL 60
STBY 03
TIME-OUT
TIME
CLEANING
MODE
STAND BY
MENU
119º
1900
STATE 5
SMOKE
SPEED
EXTR.
STOVE
STATE
D72 D73 D74
MENU
D75
14:24
21º C 23ºC
OFF
MENU
D76
14:24
21º C 23ºC
IGNITION
MENU
D77
14:24
21º C 68ºC
WORKING
MENU
21º C
SET TEMPER
D78
ROOM
D79
AMBIENT
THERMOSTAT
INSTALLATION, OPERATING AND SERVICING INSTRUCTIONS HYDRO SERIES RADIOFREQUENCY
EN