manualshive.com logo in svg

brondell RF-20, Installation Sheet, Page: 4 / 10

Share
Download
brondell RF-20 Installation Sheet Download Page 4

Questions about installation?

 Call our customer service department at 888-542-3355 or visit brondell.com 

8

STEP 1:  FAUCET INSTALLATION (cont.)

3. Attach the Escutcheon to the Main Body by inserting the blue 

tubing through the Escutcheon and pushing it all the way up 
until connected to the main body.

  3

4. Install the faucet on top of the countertop or sink and feed 

the blue tubing through the hole to the cabinet below. Then 
slide the large Plastic Washer as shown up through the blue 
tubing until snug against the bottom of the countertop or 
sink hole. Be sure that the flat part of the Plastic Washer is 
facing up and the raised area is facing down, as shown here.

  4

  5

5. Install the “Lock Washer” and the “Locking Nut” the same way 

and tighten until the plastic washer is holding the faucet 
assembly firmly in place. The faucet is now installed!

6. Pull the plastic tab out from the battery compartment to 

activate the faucet indicator.  The LED light will blink red 
once, blue once, and then will be ready to go.

PRODUCT INSTALLATION (cont.)

PRODUCT INSTALLATION (cont.)

Summary of Contents for RF-20











Reviews:

No comments