manualshive.com logo in svg

brondell RF-20, Installation Sheet, Page: 3 / 10

Share
Download
brondell RF-20 Installation Sheet Download Page 3

Questions about installation?

 Call our customer service department at 888-542-3355 or visit brondell.com 

7

PRODUCT INSTALLATION

STEP 1:  FAUCET INSTALLATION

Before Installation

You will need an existing faucet hole at least 7/16 
inches in diameter in the sink or countertop to install 
the supplied filtered water faucet. You may also 
replace an existing kitchen sprayer, soap dispenser, 
or plug already on the countertop or sink.

1. Unpack the faucet and insert the Top Spout into the Main 

Body by pushing down until inserted then screw the Top Cap 
clockwise until secured in place.

2. Cut zip tie on the blue water connection tubing and unroll 

to straighten tubing. Be careful not to cut the tube when 
removing the zip tie.

If drilling a new hole is required for the 
faucet installation, please consult a 
professional. Brondell will not be liable for 
any damages including those to  the sink 
or countertop due to installation of the 
faucet or drilling a hole.

For California Residents:

  CR2032 

batteries contain Perchlorate Material - 
special handling may apply. Visit http://
www.dtsc.ca.gov/hazardouswaste/
perchlorate for more information.

Please find answers to Frequently Asked 
Questions (FAQs) and installation videos 
on brondell.com

  1

Locking Nut

Plastic Washer

Top Spout

Top Cap

Main Body

Lock Washer

Counter Top

1/4" Tube

(connected to faucet)

Escutcheon

LED Display

Battery Seat

(CR2032)

Battery

PRODUCT INSTALLATION

Summary of Contents for RF-20











Reviews:

No comments