Broaster 1600 Service Manual Download | Manualshive

Page: 98 / 131

background image

8-5

Use repair kit #15279.

1. Remove two allen screws which attach

the valve assembly to the cooking
well.

2. Remove valve from the unit.

3. Loosen locking nut (9) then remove

valve control yoke (10) from the stem
assembly (11).

4. Remove entire stem assembly from

the housing (12) by pushing on
threaded end of the stem assembly.

5. Remove all components from the stem

assembly (11).

6. Clean then dry all metal components,

not replaced, with hot water and a mild
detergent.

7. Install new parts from the repair kit.

Lubricate all O-rings and contacting
surfaces with olive oil.

8. Mount valve assembly back on cook-

ing well with the allen screws. When
the open end of the yoke pointing to
the left.

9. With control arm in the “CLOSED”

position, a distance of 1/16” should be
maintained between the control yoke
(10) and control rod. While locking nut
(9) is loose, adjust distance in the
pressure port located on inside top of
the cooking well. Using a screwdriver,
turn stem assembly (11) either clock-
wise or counterclockwise to obtain this
distance.

10. Tighten locking nut.

Repair:
Effective: SE8D101763 and SG8D100830

broaster.com Manual #14680 3/99 Rev 5/14

«
...
96
97
98
99
100
...
»

Summary of Contents for 1600




































































































































Reviews:

No comments

Related manuals for 1600

Brand: GE Pages: 7

Brand: GE Pages: 1

Brand: GE Pages: 3

Brand: GE Pages: 36

Brand: GE Pages: 16

Spacemaker DSXH47

Brand: GE Pages: 48

Profile DPVH880EJ

Brand: GE Pages: 4

Brand: Hyco Pages: 8

Brand: Gourmia Pages: 20

Brand: T-Fal Pages: 11

Warner Howard Airstream Whisper

Brand: PHS Pages: 2

Brand: T-Fal Pages: 46

Brand: Maytag Pages: 44

Brand: Tower Hobbies Pages: 20

Brand: GEAppliances Pages: 15

Brand: Haier Pages: 20

Brand: Haier Pages: 20

Brand: Haier Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands