Broan BWT1 Series Installation Manual Download Page 5

MODELS BWT1304SS • BWT1304SSB •

BWT2304SS • BWT2304SSB

Page 5

INSTALL THE HOOD MOUNTING BRACKET

C

L

1. Construct wood wall framing that is flush with 

interior surface of wall studs.

 Make 

sure:

  a) the framing is centered over installation 

location.

  b) the height of the framing will allow the 

mounting bracket to be secured to the framing 
within the dimensions shown.

2.  After wall surface is finished, carefully center and 

level the hood mounting bracket and secure it 
to wall framing with (3) no. 8 x 1½” mounting 
screws. Tighten the screws completely.

 

NOTE: Do not use drywall anchors.

101⁄

16

41

7

/

8

” = bottom of hood 30” above cooktop

51⁄

32

FRAMING BEHIND 

DRYWALL

1

9

16

WALL STUDS

NOTE: 
  Minimum hood distance above cooktop must not be less than 24”.
  Distances over 36” above the cooktop are at the installer’s and user’s discretion - providing that ceiling height and flue length permit.

MOUNTING BRACKET LOCATION
(ABOVE 36” HIGH COOKTOP)

NOTE:

On 8-ft. ceilings

Hood distance above cooktop is:
Minimum 24”, Maximum 36” (for both ducted and 
non-ducted discharge

On 9-ft. ceilings

Hood distance above cooktop is:
Minimum 32”, Maximum 36” (for both ducted and 
non-ducted discharge)

On 10-ft. ceilings

Hood distance above cooktop is:
Minimum 32”, Maximum 36” (for both ducted and 
non-ducted discharge).

NOTE: 10-ft. ceilings require 10-ft. Flue 
Extension, Model FXN53SS for ducted or 
non-ducted installations 
(purchase separately).

CEILING 

HEIGHT

DUCT 

METHOD

HOOD DISTANCE ABOVE 36” COOK TOP

24”

25”

26”

27”

28”

29”

30”

31”

32”

33”

34”

35”

36”

MOUNTING BRACKET LOCATION ABOVE 36” HIGH COOK TOP

8 FEET

DUCTED

35-7/8”

36-7/8”

37-7/8”

38-7/8”

39-7/8”

40-7/8”

41-7/8”

42-7/8”

43-7/8”

44-7/8”

45-7/8”

---

---

NON-DUCTED

35-7/8”

36-7/8”

37-7/8”

38-7/8”

39-7/8”

40-7/8”

41-7/8”

42-7/8”

 

43-7/8”

44-7/8”

45-7/8”

---

---

9 FEET

DUCTED

---

---

---

---

---

---

---

---

43-7/8”

44-7/8”

45-7/8”

46-7/8”

47-7/8”

NON-DUCTED

---

---

---

---

---

---

---

---

43-7/8”

44-7/8”

45-7/8”

46-7/8”

47-7/8”

10 FEET

DUCTED

---

---

---

---

---

---

---

---

43-7/8”

44-7/8”

45-7/8”

46-7/8”

47-7/8”

NON-DUCTED

---

---

---

---

---

---

---

---

43-7/8”

44-7/8”

45-7/8”

46-7/8”

47-7/8”

Summary of Contents for BWT1 Series





































Reviews: