Broadcom BCM1125 User Manual Download Page 299 | Manualshive

Page: 299 / 516

background image

User Manual

BCM1250/BCM1125/BCM1125H

10/21/02

B r o a d c o m C o r p o r a t i o n

Document

1250_1125-UM100CB-R

Section 9: Ethernet MACs Page

271

T

RANSMITTER

O

PERATION

T

RANSMITTER

C

ONFIGURATION

The transmitter clock is accepted as an input from the PHY device for 10/100 Mbit/s operation. However, for 1
Gbit/s operation the data lines are clocked at 125 MHz so the clock is forwarded with the data. In this case the
reference clock input is used (on the BCM1250, the REFCK01 pin is for interfaces E0 and E1, and the REFCK2
pin for interface E2; on the BCM1125/H, REFCK0 is for E0 and REFCK1 for E1). The clock source is
configured by the MAC speed selection in the

mac_cfg

register.

The transmit FIFO is a 64 bit wide fifo with 128 entries.

shows the thresholds that are used to

configure it. When the FIFO has space for data it will signal the DMA engine to request data. The tx_wr_thrsh
field in the

mac_thrsh_cfg

sets the number of empty entries there must be in the FIFO before it will request

data. The DMA engine fetches either 32 bytes or 64 bytes at a time, so this value should be set to 4 or 8.

The data from the transmit FIFO is read out by the protocol engine for transmission. Once transmission of a
packet has started the DMA engine must ensure that there is always data in the FIFO when the protocol engine
needs it. If the FIFO is empty at any time before the end of the packet then an underflow error is reported and
transmission fails (in encoded Packet FIFO mode the transmission will not fail, instead cycles with no valid data
will be inserted in the link protocol). To reduce the likelihood of the FIFO becoming empty the tx_rd_thrsh
threshold can be set to ensure a certain number of entries have been written to the FIFO before transmission
starts.

Figure 54: Transmit FIFO Thresholds

Errors that happen between

SOP and this entry can be

automatically retried

FIFO must be filled to here
before SOP will be sent

64 bit wide

tx_rd_thrsh

tx_rl_thrsh

Start of

Packet

S

O

P

tx_wr_thrsh

The FIFO will request
data if at least this
much is empty

«
...
297
298
299
300
301
...
»

Summary of Contents for BCM1125





































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for BCM1125

Brand: IDT Pages: 281

DMX-Universal-Demux

Brand: DMX4ALL Pages: 17

Brand: Rockwell Automation Pages: 108

EK-FB GA AX370 Gaming RGB Monoblock

Brand: ekwb Pages: 2

Brand: T.A Pages: 11

Brand: VCS Pages: 118

Brand: DigiTech Pages: 6

Brand: Idis Pages: 20

UniFi LED ULED-AT

Brand: Ubiquiti Pages: 16

640 - Pentium 4 640 3.2GHz 800MHz 2MB Socket 775 CPU

Brand: Intel Pages: 105

Brand: Xenteq Pages: 16

Brand: Maxtor Pages: 2

Brand: Doremi Pages: 15

Brand: Xtreme Pages: 83

Brand: Vacron Pages: 16

Brand: Taiwan Commate Computer Inc. Pages: 25

Brand: Greenlee Pages: 52

Brand: Intel Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands