Broadcast Tools Universal 4.1 MLR/Serial Installation And Operation Manual Download Page 1

Installation and Operation Manual

P R O B L E M   S O LV E D

Due to the dynamic nature of product design, the information contained in this 
document is subject to change without notice.  Broadcast Tools, Inc., assumes no
responsibility for errors and/or omissions contained in this document.  Revisions 
of this information or new editions may be issued to incorporate such changes.

Broadcast Tools® is a registered trademark of Broadcast Tools, Inc.

All Sentinel® labeled products are registered trademarks of Broadcast Tools, Inc.

Copyright® 1989 - 2017 by Broadcast Tools, Inc.  All rights reserved. 

No part of this document may be reproduced or distributed without permission.

Visit www.broadcasttools.com for important product update information.

Manual update:  7/1/2017

Firmware version 1.0 and higher. If you need a firmware upgrade, contact Broadcast Tools®.

No part of this document may be reproduced or distributed without permission.

ALL SPECIFICATIONS AND FEATURES FOR THIS PRODUCT ARE SUBJECT TO

CHANGE WITHOUT NOTICE

NOTE: We recommend the use of Chrome, Firefox or Safari as your browser.

Universal 4.1 MLR/Serial

Switcher/Router with Mechanical Latching Relays

INC

®

Summary of Contents for Universal 4.1 MLR/Serial


















Reviews: