manualshive.com logo in svg

Brivo Allegion AD400, Configuration Manual, Page: 7 / 11

Share
Download
Brivo Allegion AD400 Configuration Manual Download Page 7

© 2018 Brivo Systems LLC. All rights reserved.

P-MAN-PUB-Allegion AD400 

Configuration Guide 1.0

7

Allegion AD400 Configuration Guide

Associating Allegion AD400 Devices with Brivo 

Onair

The Allegion PIM400-485 unit and Allegion AD400 Wireless Lock Device features allow administrators to assign and 

configure Allegion PIMs and Locks attached to the Brivo Onair panel. 

Creating an Allegion Panel Interface Module

Note: Within Brivo Onair, a PIM400-485 unit is identified as an Allegion Gateway.

1. 

Scroll over the 

Setup link. The sub-navigation menu displays.

2. 

From the sub-navigation menu, scroll over the 

Sites/Doors tab and click Control Panels from the    

 

 

dropdown list. The Control Panels List page displays.

3. 

Select the desired control panel to which you wish to associate the Allegion PIM400-485.

4. 

Scroll over and click the 

More Operations tab.

5. 

Scroll over and click the 

Add Wireless/Gateway/Router tab. 

6. 

The Add Wireless Gateway/Router page appears. Click on the 

Wireless Board Types dropdown menu.

Summary of Contents for Allegion AD400












Reviews:

No comments