1a
Hold the handle and lift upwards until
the chassis is fully extended and clicks
into position
(dia 1b)
.
1b
Push the rear wheel assembly into the
rear wheel axle
(dia 1c)
. Check the
wheel is correctly fitted by trying to
pull it out. Repeat this process for both
wheels.
1c
Adjust the handle to a comfortable
height by simultaneously pressing the
buttons on the inside of the handle –
on both sides
(dia 1d)
.
Check the chassis is ready for use by
pressing down on the handle – the
chassis should not collapse.
WARNING –
Ensure that all locking
devices are engaged before use.
1d
1 Assembling your chassis
IMPORTANT –
Always remove
your child from the seat unit prior to
installation, removal or change of seat
direction. The seat unit can be installed
forward or rearward facing.
To install the seat unit, insert the
seat locking latches into both chassis
sockets
(dia 2b).
2b
To fit the hood align with the fixings on
the bumper bar and slide down
(dia 2f)
until fully engaged.
The hood can be fitted without the
bumper bar by aligning with the fixings
on the seat unit and sliding down until
fully engaged.
2f
Push down on the seat until you hear an
audible ‘click’
(dia 2c)
.
WARNING –
Check that the seat
unit attachment devices are correctly
engaged before use by lifting the seat.
2c
To open the hood, pull the front of
the hood forward then push the hood
hinges down on both sides
(dia 2g)
.
To remove the hood, slide the hood off
the fixings on the seat unit, or off the
fixings on the bumper bar (if fitted).
2g
To adjust the backrest, squeeze the
backrest adjuster lever at the top of the
seat unit, then raise or lower the seat
unit to the desired position
(dia 2h)
.
IMPORTANT –
Use the harness at
all times.
IMPORTANT –
Do not lift the stroller by
the seat unit.
IMPORTANT –
Support the back of the
pushchair seat unit when adjusting the
angle.
2h
Release the storage latch
(dia 1a)
.
To attach the bumper bar
(dia 2e)
,
remove the hood (if fitted). Align the
bumper bar mouldings with the fixings
then slide both bumper bar mouldings
onto the seat unit until fully engaged.
To remove the bumper bar, remove the
hood (if fitted) then slide both bumper
bar mouldings off the seat unit fixings.
WARNING! DO NOT
lift the stroller
by the bumper bar or hood. It may
disengage or damage your product.
2e
HANDY HINT –
You may find it helpful
to apply the brake when fitting the seat
unit.
Push down on the brake lever to lock
the brakes . To release the brake lift
brake lever
(dia 2a)
.
IMPORTANT –
Always apply the
brakes when you park the stroller.
2a
A
B
B
A
Unfasten the comfort pad to reveal the
five-point harness. A five-point harness
is provided to restrain your child
(dia 2i)
.
To secure the child in the harness, push
buckle A and B into buckle housing
C until the buckle prongs snap into
position. Carefully adjust the harness by
pulling the slider until the desired fit is
achieved in the waist belt, shoulder and
crotch straps.
Always adjust the harness when
changing the seating position of the child.
To release the buckle, squeeze the top
and bottom prongs A .
WARNING –
Always use the crotch strap
in combination with the waist belt.
WARNING –
Fasten the harness when
not in use to prevent it becoming trapped
when folding the stroller.
2i
D
D
D
A
B
C
To lock the swivel wheel, push lock
towards . To unlock swivel wheel,
push towards
(dia 2d)
.
HANDY HINT –
The front wheel should
be locked when used on uneven
surfaces or mounting kerbs.
2d
B
A
A
B
A
B
C
D
A
2 Attaching your seat unit and using your stroller
(this vehicle is intended for children from 6 months and up to 15kgs)
IMPORTANT
- A V-Type seat unit must be used with this V-Type chassis
3 Folding your stroller
IMPORTANT –
Always remove
your child from the seat unit prior to
installation, removal, change of seat
direction or folding.
3a
Push the handle down allowing the
chassis to fold until it moves into the
fully folded position. Ensure that the
storage latch is closed
(dia 3c)
.
HANDY HINT –
The chassis may also
be folded with the seat unit attached.
3c
HANDY HINT –
For a more compact
storage, fold the handle down. Refer
to
(dia 1d)
for instruction on operating
handle adjustment.
Stand at the rear of the chassis, pull
both release latches and twist the right
hand one in the direction of the arrow
marked on the release latch
(dia 3b)
.
3b
To remove the rear wheels, push
the locking button and pull the
corresponding rear wheel out
(dia 3d)
.
3d
1408.001 - Vigour 3 (UK).indd 2
5/6/07 10:31:30
