9.2 BUCKLE UP YOUR CHILD
Product variant KING II:
Product variant KING II LS:
WARNING!
Pull the adjuster strap 16
straight
forward (not upwards or downwards)
1.
Pull the adjuster strap 16 until the indicator light 15
illuminates “green“ and you can hear an audible
sound.
►
The belt tensioning of your child seat is now active
and removes excess belt length automatically.
TIP!
The green indicator light 15 turns off automatically
after a few seconds
, but the system continues to work.
Your child seat has a system that automatically keeps the tension in the
belt once adjusted correctly. The system works with an occupant sensor, so
without your child sitting in the seat the indicator light will be off.
Product variant KING II ATS:
DANGER!
When the indicator light 15
flashes red
and an alert sounds, your child is not properly se-
cured. Stop at the next safe opportunity and repeat
the steps of the chapter 9.3 Securing your child.
TIP!
If you are driving and you can´t stop immedi-
ately the frequency of the alert will significantly reduce
automatically after 3 mins (reminder mode).
When not driving you can put the alert into reminder
mode by pressing the indicator light 15 for 3 seconds.
DANGER!
When the indicator light 15
flashes red
and green the batteries must be replaced.
Unfold the seat cover and the foam cushion on the
seating surface and change the two type AAA batteries
in the battery compartment 24 .
8. INSTALLATION OF THE CHILD SEAT
1.
Place the child seat facing in the direction of travel
on the vehicle seat.
2.
Push one of the grey release buttons 03 and at the
same time pull the seat shell 02 as much forward
as possible.
DANGER!
When opening or closing, nothing must
come between the seat shell 02 and the seat base
06
. You or your child could pinch your fingers,
injuring them.
3.
Pull out the vehicle seat belt and place it between
seat shell 02 and seat base 06 through the two
lower light red belt guides 04 .
DANGER!
Ensure that diagonal seat belt 21 and
lap belt 22 lie in both lower light red belt guides 04
and both belts are not twisted.
4.
Engage the buckle tongue in the vehicle seat buckle
20
with an audible “CLICK“.
5.
Tighten the diagonal belt section 21 by pulling the
diagonal belt 21 strongly on the opposite side from
the vehicle seat belt buckle.
6.
Hold the seat shell 02 with one hand while pulling
the grey
adjustment lever
05 forward with the
other hand. Tip the seat shell 02 against the seat
base 06 over both engagement positions.
WARNING
! To avoid injuries take your hand away
from the grey
adjustment lever
05 , as soon as
getting over the two engagement positions.
7.
Push the seat shell 02 with both hands against the
seat base 06 until it is fully engaged.
DANGER
! The two red safety markings on the
grey release buttons must not be visible.
8.
Place the diagonal belt section 21 in the upper dark
red belt guide 01 .
9.
Give the child seat a firm pull forwards to ensure
that it is securely fastened.
10.
Observe the steps in the chapter
10.1 “ADJUSTING THE HEADREST“
.
11.
Observe the steps in the chapter
10.2 “BUCKLE UP YOUR CHILD“
.
9. 1 ADJUSTING THE HEADREST
1. Loosening the harness
Press the adjustment button 13 and at the same time
pull below the shoulder pads 10 both shoulder straps
11 forward.
The headrest 09 must be adjusted so that there is a
space two fingers wide between the headrest
09 and
your childs shoulders.
2. Adjusting the headrest for:
KING II ATS / LS
1.
Have your child sit down in the seat and check the
height.
2.
Pull / push the headrest adjuster 07 into the desired
direction.
3.
Repeat the procedure until the headrest 09 has the
correct height.
KING II
1.
Pull the leaver of the headrest adjuster 08 at the
rear of the seat shell 02
Now the headrest is unlocked.
2.
Slide the unlocked headrest adjuster 09 into the
desired diection to the correct height. As soon as
you release the leaver of the headrest adjuster 08
, the headrest 09 engages.
3.
Have your child sit down in the seat and check the
height. Repeat the procedure until the headrest
09
has the correct height.
A correctly set headrest 09 ensures that the 5-Point harness is optimally
positioned, and gives your child optimum protection.
To adjust the height of the headrest to fit your child:
The seat shell of the KING II / ATS / LS can be put into four different angles:
DANGER!
● The batteries must be replaced by an adult.
● Keep batteries out of the reach of children.
● Use only new batteries of the same type.
● Use only 2x AAA type, 1.5 volts batteries.
● Never use batteries that show signs of leakage.
● Remove the old batteries and dispose of them according to the disposal
instructions on page I, chapter 5.
● Do not expose the batteries to excessive heat or fire, the batteries may
burst or explode.
● Due to lower voltage do not use rechargeable batteries.
● Observe the warning on the packaging of your batteries.
them before putting
them into the harness
buckle 12 - this should
make a clicking noise.
9.
Pull shoulder straps 11
to remove all slack from
the lap section ensuring
the harness lies flat.
1.
Open the harness buckle 12 (press red button)
2.
Press the adjusting button 13 and at the same time
pull below the shoulder pads 11 both shoulder
straps 10 forward.
3.
Insert the buckle tongues 23 into the harness retainer
19
4.
Have your child sit down in the child seat.
5.
Check the correct height of the headrest and adjust
them if necessary [see above].
6.
Make sure that your child´s back lies flat against the
backrest of the child seat.
7.
Unhook the buckle tongues 23 .
8.
Guide the two buckle latches 23 together and engage
DANGER!
The lap belts 24 must be positioned as low as possible over
your child‘s hips.
10.
Carry out the steps in section
“9.3 SECURING YOUR CHILD“
for your
particular product variant.
1.
Pull on the adjusting strap 16 until the harness lies
flat and is close against your child‘s body.
WARNING!
Pull the adjuster strap 16
straight
forward (not upwards or downwards).
1.
Pull the adjuster strap 16 until the indicator light 14
illuminates “green“ and you can hear an audible
“Click“ which indicates that the harness is tightened
correctly.
TIP!
The green indicator light turns off automatically after
a few seconds.
2.
Observe the safety notes in the chapter
“
8. INSTALLATION OF THE CHILD SEAT
“
9.3 SECURING YOUR CHILD
WARNING!
Pull out the adjusting strap 16
straight
forward.
The more snugly the harness fits over your child‘s body, the better your child will be
protected. Therefore avoid putting thick clothes on your child under the belt.
2.
Observe the safety notes in the chapter
“
8. INSTALLATION OF THE CHILD SEAT
“
What to do when the indicator light does not illuminate “green“ ...
● Check if the headrest is adjusted correctly according to the chapter
“
9.1 ADJUSTING THE HEADREST“
.
● Ensure that you have pulled the adjuster strap with enough force.
In general the battery in the product is a non replaceable item and must not be
changed due to its long life.
If the problem can not be resolved using the above methods, contact your service
representative or the BRITAX RÖMER Customer Service.
What to do when the indcator light does not illuminate at all...
● Check if the headrest is adjusted correctly according to the chapter “
9.1
ADJUSTING THE HEADREST“
.
● Check if there is any accumulation of dirt on the seating area under the
occupant sensor.
If necessary clean the area as described in chapter 4 [page I].
● Replace both batteries
● Ensure that you have pulled the adjuster strap with enough force.
If the problem can not be resolved using the above methods, contact your service
representative or the BRITAX RÖMER customer service.
Please take the time to read these instructions carefully and keep
them to hand in the intended storage compartment
18
on the child
safety seat at all times! The instructions must be with the child safety
seat if the latter is passed on to a third party.
DANGER! For the protection of your child:
• Use the KING II / ATS / LS exclusively for securing your child in your
vehicle. It is in no way suitable as a seat or toy in the home.
• In the event of an accident with a collision speed of more than 10 km/h, the
child safety seat may be damaged without the damage becoming immediate-
ly visible. In this case the child safety seat must be replaced. Please dispose
of it properly.
•
Have your child safety seat checked as a rule if it was damaged (e.g if it
falls to the ground).
• Regularly check all important parts for damage. Ensure that all mechanical
parts, in particular, are fully functional.
• Never lubricate or oil parts of the child seat.
•
Never leave your child unattended in the child seat in the vehicle.
•
Let your child in and out of the vehicle from the pavement side as a rule.
• Protect the child safety seat against intensive direct sun radiation,
as long as it is not in use.The child safety seat can become very hot under
direct sun radiation. Child skin is sensitive and could thereby be injured.
•
The more snugly the harness fits over your child's body, the better your child will
be protected. Therefore avoid putting thick clothes on your child under the belt.
• Take regular breaks on long journeys in order to give your child the opportu-
nity to play around when removed from the child seat.
• Use on the rear seat: Push the front seat forwards sufficiently so that the
feet of your child cannot hit the backrest of the front seat (to avoid the risk
of injury).
DANGER! For the protection of all vehicle occupants:
In the case of an emergency stop or an accident, unsecured persons or
objects may cause injury to other vehicle occupants. Please always check
that...
• the backrests of the vehicle seats are locked (i.e. that a foldable rear seat
bench latch is engaged).
• all heavy or sharp-edged objects in the vehicle (e.g. on the parcel shelf) are
secured.
• all persons in the vehicle have their seatbelts fastened.
• the child safety seat is always secured when it is in the vehicle, even if no
child is being transported.
WARNING! For your protection when handling the child seat:
• Never use the child safety seat free-standing, not even for test sitting.
• When opening or closing, nothing must come between the seat shell 02
and the seat base 06
. You or your child could pinch your fingers, injuring
them.
• To avoid damage, ensure that the child safety seat is not jammed in between
hard objects (car door, seat rails, etc.).
• Keep the child safety seat in a safe place if it is not in use. Do not place any
heavy objects on the seat and do not store it directly next to sources of heat or
in direct sunlight.
CAUTION!
To protect your vehicle:
• Certain car seat covers made from more sensitive materials (e.g. velour, leath-
er, etc.) may sustain signs of wear and tear when using child safety seats. For the
optimum protection of your car seat covers, we recommend using the BRITAX
RÖMER Car Seat Protector from our accessories programme.
6. SAFETY NOTES
PAGE II
7. ANGLE ADJUSTMENT
To adjust the angle:
Lift the adjustment handle 17 and pull/push the seat
shell 02 into the desired position.
DANGER!
The seat shell 02 must engage secu-
rely regardless of its position. Pull on the seat shell
02
to ensure that it is engaged properly.
TIP!
You can also adjust the angle of the seat shell
02
when your child is sitting in the child seat.
For the safety of your child, before every journey in the car check
that ...
►
the child safety seat is securely fastened,
►
seat shell 02 and seat base 06 are fully engaged. The both red safety
marks on the grey release buttons 03 must not be visible.
►
the diagonal 21 and the lap seat belt sections 22 run on both sides
through the light red lower belt guides 04 ,
►
the diagonal seat belt section 21 runs through the upper dark red belt
guide 01 ,
►
diagonal 21 and lap seat belt sections 22 are tight and
not
twisted,
►
the vehicle seatbelt buckle 20 is
not
positioned between the lower light
red belt guides 04 of the child seat.
►
the headrest is adjusted correctly,
►
the 5-point harness of your child seat are comfortable but FIRM fit around
your child,
►
the straps of the 5-point harness are
not
twisted,
►
the buckle tongues 23 are engaged in the harness buckle 12 .
DANGER!
If your child tries to open the vehicle belt buckle 20 , or the 5-point
harness buckle 12 stop immediately as soon as safely possible. Check
whether the child safety seat is correctly fastened and ensure that your child
is correctly secured. Explain to your child the dangers associated with their
actions.
UNFASTENING YOUR CHILD AND REMOVAL:
To unfasten your child or to remove the child safety seat, observe the
steps in Section
5 “DISASEMBLY AND DISPOSAL“
[PAGE I]
02
17
02
03
06
02
06
04
04
20
05
02
06
21
01
06
02
03
16
12
23
12
13
11
10
09
13
11
10
07
09
08
02
beep!
beep!
16
15
24
15
15
15
15
16
15
21
22
24
11
