manualshive.com logo in svg

Bristan Thermostatic Power Shower 1000, Installation Instructions & User Manual

Share
Download
Bristan Thermostatic Power Shower 1000 Installation Instructions & User Manual Download Page 8

88

9

Fitting your Shower

COLD

L

N
E

Refit unit to pipes and secure to wall using 32mm x No. 8 screws 

provided.

Connect the wire which may be coloured Brown or Red to the 

terminal marked 

L

. Connect the wire which may be coloured Black 

or Blue to the terminal marked 

N

. Connect the wire which may be 

coloured Yellow/Green to the terminal marked 

E

. 

Secure into position with the cable clamp and tighten the two fixing 

screws.

Do not fit the front cover at this stage refer to the commissioning 

procedure.

Note: If the electrical supply cable is concealed in the wall ensure 

that it avoids the unit’s fixing points so that fixing screws do not 

pierce the cable.

HOT

COLD

Need help?

 Give us a call on

 0844 701 6273

 and speak to one of our trained advisors.  

Wall fixing points

Electrical connections

Cable Clamp

Cable Connector

Summary of Contents for Thermostatic Power Shower 1000

















Reviews:

No comments

Brands by name

Popular brands

Load more brands