Bristan Thermostatic Power Shower 1000 Installation Instructions & User Manual Download Page 14

14

14

15

Guarantee

Need help?

 Give us a call on

 0844 701 6273

 and speak to one of our trained advisors.  

Guarantee 

Thank you for purchasing a Bristan product. This product 

has been designed and tested, in the UK, to the highest 

standards.

Guarantee: 2 Year parts. 

  1 Year labour (subject to registration). 

This guarantee applies to products purchased within the 

United Kingdom or Republic of Ireland, but does not apply 

to products used commercially.

This is provided that:

1. The guarantee registration card is completed and 

returned within ten days complete with a copy of proof of 

purchase. Proof of purchase is required for any servicing 

requirements.

2. The product is installed and operated in accordance with 

our instructions and has not been misused or damaged.

This in no way affects your statutory rights as a consumer. 

The information on the Guarantee card helps Bristan to 

process any claims and contact you about your product 

and its maintenance if required. The registration of your 

personal details is purely for Bristan use and the remaining 

information helps us to make products for the future.

Should a complaint arise, products are guaranteed against 

faulty workmanship and materials for a period of 12 

months from the date of purchase, when in domestic use 

(second year guarantee is parts only). For your guarantee 

to be valid, your shower must be installed by a competent 

person, in accordance with the instruction manual. 

Bristan will repair or replace (at our option), free of 

charge, any faulty components during the guarantee 

period, provided it has been maintained and operated 

in accordance with our instructions, and has not been 

misused or damaged.

Modification or repair of this product by person(s) not 

authorised by Bristan will invalidate this guarantee.

This guarantee does not affect your statutory rights.

Service Policy 

Replacement Parts Policy

Important: 

In the event of product or component malfunction,  

DO NOT tamper with or remove the product from site. 

Telephone the Customer Services Department and be 

prepared with the date of purchase, model number and  

a clear description of the complaint.

Our service staff are fully qualified to advise on correct 

installation procedures and will be able to diagnose 

whether the fault will require a replacement part or a visit 

from a Bristan engineer.

If required, a service call will be booked and either yourself 

or an appointed representative (who should be a person of 

18 years or over) must be present during the visit. 

All site visits to product within the guarantee period will 

be carried out free of any parts or labour charges provided 

the conditions of the guarantee have been adhered to (the 

second year guarantee is parts only).

All site visits to product out of guarantee will be subject to 

charges for parts and labour. Charges will also be levied on 

cancelled appointments, unless advised to Bristan at least 

24 hours in advance of the agreed date and time.

Should a product be discontinued, spare parts stocks 

will be maintained, but in the event of a part becoming 

unavailable Bristan reserve the right to supply a substitute 

of equal quality.

For spare parts please contact Customer Services or via 

the Bristan website. 

Opening times: Please refer to the Bristan website.

Customer Service: 

Tel: 0844 7016273 • Fax: 0844 7016275
E-mail: [email protected]

Summary of Contents for Thermostatic Power Shower 1000

















Reviews: