Brinly-Hardy S100-12020 Quick Start Manual Download Page 5

English Manual

5

1020313-A

Safety Precautions

12. Look behind and down before backing up to be 

sure of a clear path.

13. Never carry passengers.
14. Use care when loading or unloading the machine 

into a trailer or truck.

15. Be careful when crossing gravel paths or roadways.
16. Always have your feet and hands clear of the 

controls when starting the engine.

17.  Always park the spreader and start the engine on 

a level surface with the ground speed control 

levers in neutral, the free wheel lever in bypass, 

and the park brake engaged.

18. Never leave the spreader unattended without 

placing the spreader on level ground, placing 

ground speed control levers in neutral, engaging 

the park brake, shutting off the engine and closing 

the fuel shutoff valve.

19. To avoid serious burns, do not touch the engine or 

muffler  while  the  engine  is  running  or  until  it  has 

cooled for at least 30 minutes after it has been shut 

off.

20. If you hit a solid object while spreading, place the 

ground speed control levers in neutral, engage the 

park brake and stop the engine. Disconnect the 

spark plug wire and inspect for damage. Repair 

any damage.

21. Always disconnect the spark plug wire to prevent 

the engine from accidentally starting before 

performing any maintenance on this spreader.

22. Keep the machine and especially the engine/

transmission area clean and free of grease, grass 

and leaves to reduce the potential for overheating 

and fire.

23. Do not exceed hopper capacity listed in 

Specifications Section.

24. To prevent injury from hand, never place hands 

into hopper while fan is spinning.

SOME OF THE FOLLOWING PRECAUTIONS 

ARE BASED ON ANSI B71.4-2004: 

Specifications

NOTE: 

The engine manufacturer is responsible for  

all engine-related issues with regards to performance, 

power-rating, specifications, warranty and service. 

Please refer to the engine manufacturer’s owner’s/

operator’s manual, packed separately with your  

unit, for more information.

MODEL

S100-12020

Engine Mfg.

Honda

HP

4.3HP @ 3600 RPM

Type

4 Cycle Single Cylinder

Starter

Recoil

Air Cleaner

Foam element over paper 

element

Lube

Splash

Fuel Capacity

1.4L (0.37 gal)

Traction Drive

Tuff Torq, 

 

Model K57R Hydrostatic

Hydraulic Filtration

Internal

Ground Speed

0 to 6 mph

Wheels

Rear:  18 x 6.50-8   

Front:  13 x 5.60-6

Width

36”

Height

49”

Length

60”

Weight

330 lbs

Maximum Hopper 

Weight Capacity

120 lbs (do not exceed)

Summary of Contents for S100-12020

















Reviews: