Briggs & Stratton SpeedClean 020239-1 Owner'S Manual Download Page 15

SpeedClean™ 2200 PSI Pressure Washer

15

3.

Tilt pressure washer to drain oil into an approved
container until it drips slowly from pump.

4.

Tilt pressure washer in opposite direction and empty
premeasured pump oil bottle into same opening (a
small funnel may be helpful).

5.

Install black pump oil cap and tighten firmly.

6.

Set pressure washer in upright position. Add fuel and
engine oil.

ENGINE MAINTENANCE

See the engine owner’s manual for instructions on how to
properly maintain the engine.

KEEP OUT OF REACH OF CHILDREN. DON'T
POLLUTE. CONSERVE RESOURCES. RETURN
USED OIL TO COLLECTION CENTERS.

PREPARING THE  UNIT

FOR STORAGE

Water should not remain in the unit for long periods of
time. Sediments or minerals can deposit on pump parts and
“freeze” pump action. If you do not plan to use the pressure
washer for more than 30 days, follow this procedure:

1.

Flush chemical injection hose by placing filter into a pail
of clean water while running pressure washer in low
pressure mode (adjustable nozzle in forward position).
Flush for one to two minutes.

2.

Shut off engine and let it cool, then remove high
pressure and garden hoses. Disconnect spark plug wire
from spark plug.

3.

Place the spray gun, nozzle extension, floor brush,
utility brush, brush extension and high pressure hose in
the accessory storage bag.

4.

Empty pump of all pumped liquids by pulling recoil handle
about 6 times.This should remove most liquid in pump.

5.

Use PumpSaver to prevent corrosion build up and
freezing of pump.

6.

Store unit in a clean, dry area.

Protecting the Pump

To protect the pump from damage caused by mineral
deposits or freezing, use PumpSaver to treat pump.This
prevents freeze damage and lubricates pistons and seals.

NOTE: PumpSaver is available as an optional accessory. It
is not included with the pressure washer. Contact the
nearest authorized service center to purchase PumpSaver.

To use PumpSaver, make sure the pressure washer is turned
off and disconnected from supply water. Read and follow all
instructions and warnings given on the PumpSaver container.

NOTE: If PumpSaver is not available, draw RV antifreeze
(non-alcohol) into the pump by pouring the solution into a
3-foot section of garden hose connected to inlet adapter
and pulling recoil handle twice.

STORING THE  ENGINE

See the engine owner’s manual for instructions on how to
properly prepare the engine for storage.

CAUTION

• Failure to do so will permanently damage your pump and

render your unit inoperable.

• Freeze damage is not covered under warranty.

You must protect your unit from freezing temperatures.

• Always wear eye protection when using PumpSaver.

Read and follow all cautions and warnings on the
PumpSaver can label.

CAUTION

• Used motor oil has been shown to cause skin cancer in

certain laboratory animals.

• Thoroughly wash exposed areas with soap and water.

Avoid prolonged or repeated skin contact with used
motor oil.

CAUTION

CAUTION

• Protect surfaces from dripping PumpSaver.

PumpSaver will drip from pump after treatment and
will stain wood and concrete.

Summary of Contents for SpeedClean 020239-1

































Reviews: