19
mixture, first pour gasoline into a special container (canister), then oil and mix. It is recommended to use the special
container included in the set, in which the amount of gasoline and the amount of oil to be added are marked. The whole
should be mixed thoroughly.
Attention!
Dealing with fuel should be carried out outdoors, in an open area away from sources of ignition, sparks and flames. When
refueling, the engine should be immobilized, no smoking, no cellular phone allowed. The engine must not be hot during
refueling.
Focus on what you are doing. The fuel canister or fuel tank of the brushcutter should be shaken before each use (possibility
of delamination of the mixture).
To fill the combustion tank. Unscrew the fuel filler cap and pour the mixture using a funnel, being careful not to spill fuel.
If fuel has spilled, wipe it off with a dry cloth.
Important!
Too low a fuel level in the tank (below 1/3 volume) may cause unstable engine operation. During operation, check the fuel
level in the tank.
FIRST START OF THE ENGINE
To activate the device:
Always hold the device.
Turn the switch on the right handlebar to the
"I"
position (on)
2
(
Fig. 1).
Several times (4-8 times) press the manual fuel pump
17 (Fig. 2)
to bring fuel to the carburetor (it should be
pumped until fuel appears in the pump).
With one hand, holding the brushcutter so that it is stationary, pull the starter handle once without jerking
11 (Fig. 2)
checking that the engine is warm and starting.
If the engine did not start, move the choke lever
15 (Fig. 2)
into the suction position
. Then pull the starter
rope until the first cycle of work.
Press the gas lever lock
1 (Fig. 1)
then the gas
lever
3 (Fig. 1)
to turn off choke (choke is automatic)
Then pull the starter rope to start the device.
If the engine does not start after a few attempts, check the troubleshooting table.
MOWING THE GRASS
Read the safety instructions in this manual before mowing. If you have no experience, check the balance and behavior of
the brushcutter without starting the engine.
CAUTION!
The first 10 hours of mowing the grass are recommended when using a trimmer head.
You can turn the device off at any time by switching the power button
2 (Fig. 1)
to position
"0".
Attention!
Periodically remove grass fibers wrapped around the cutting tool axis to prevent the drive axle from
overheating. Deposits of grass fibers and weeds are tangled around the drive axle under safety cover. This prevents
proper cooling of the propeller shaft and gearbox. Remove grass deposits with a screwdriver or similar tool only when the
machine is turned off.
EJECTING THE CUTTING LINE
If the line is too short, pull it out.
The brushcutter is equipped with a bumper head
(Fig. 19).
To eject the cutting line automatically - lightly tap the head on the
ground to eject the cutting line. During this operation, remember that too hard or too violent impact of the head against the
ground can damage it, so a better way is to manually eject the cutting line.
To eject the line manually:
press the button in the drum with the fishing line
1 (Fig. 19),
pull out the fishing line to the desired length,
if the line turns out to be too long, a cutting knife installed in the cover
2 (Fig. 19)
cuts the line to the right length.
Summary of Contents for NAX 700B
