Bridgeview Bale King 6100 Operator'S & Parts Manual Download Page 7 | Manualshive

Page: 7 / 65

background image

Bale King 6100 – Operator and Parts Manual

7 / 65

Introduction

Thank you for purchasing the Bale King 6100 Bale processor by Bridgeview
Manufacturing. By following the instructions in this manual, the Bale King will
provide you with years of trouble free operation.

This  document  is  a  complete  safety,  operation  and  parts  manual  for  the  Bale  King
6100. The manual explains how to safely and effectively use your bale processor. The
procedures  outlined  in  this  manual  must  be  followed  to  ensure  safe  operation  and
longevity of your machine. The parts section of this manual lists all the parts you may
need to order in case of accident or breakdown.

!!BEFORE OPERATING YOUR MACHINE, READ THIS

MANUAL ENTIRELY!!

Warranty Information

Bridgeview Manufacturing Inc. provides warranty to

the BALE KING 6100 series to its original owner for a
period of two years

from the date of purchase according to

the following provisions:

Normal Farm Use

Commercial, Government, or Rental Use

First year warranty covers parts* and labour.

Second year warranty covers parts* only

.

One year warranty covers parts* and labour.

*EXCEPTION

:

Flails

are considered a wearing part and are covered against breakage for

60 days

from date of purchase.

•

Warranty

does

cover manufacturing defects in original material and

workmanship.

•

Warranty

does not

cover damage to the machine and/or its components caused

by operation or maintenance outside the guidelines of this manual.

•

Warranty

does not

cover wear and tear incurred during normal operation as

outlined in this manual.

•

Warranty will be

VOID

and Bridgeview Manufacturing Inc. is not liable in any

way if the Bale King 6100 is used for any purpose other than the use specified in this
manual.

•

Tire warranty is covered by the

Tire Manufacturer.

Commented [MRP2]:

added

Commented [MRP3]:

added

«
...
5
6
7
8
9
...
»

Summary of Contents for Bale King 6100


































































Reviews:

No comments

Related manuals for Bale King 6100

Brand: ABB Pages: 86

Brand: Keithley Pages: 149

Brand: DARAY Pages: 24

Brand: Jafar Pages: 9

KOMPAN SPF28666S

Brand: Bommelland Pages: 23

Brand: Landoll Pages: 52

Brand: Gason Pages: 110

Brand: Gainsborough Pages: 2

Brand: IBS Scherer Pages: 64

Brand: Teac Pages: 9

Brand: Tascam Pages: 3

Brand: Tascam Pages: 56

Portastudio 2488

Brand: Tascam Pages: 28

Brand: Tascam Pages: 2

Brand: Tascam Pages: 5

Brand: Tascam Pages: 3

Brand: Tascam Pages: 2

Brand: Tascam Pages: 107

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands