background image

15

 This appliance must be earthed.

This appliance is fitted with either a moulded or rewirable BS1363, 13 amp plug. The fuse 

should be rated at 13 amps and be ASTA approved to BS1362. 

If the fuse in a moulded plug needs to be changed, the fuse cover must be refitted. The 

appliance must not be used without the fuse cover fitted.

If the plug is unsuitable, it should be dismantled and removed from the supply cord 

and an appropriate plug fitted as detailed below. If you remove the plug it must not be 

connected to a 13 amp socket and the plug must be disposed of immediately. 
The wires of the mains lead are coloured in accordance with the following code: 

GREEN/YELLOW  = EARTH          BLUE = NEUTRAL          BROWN = LIVE

The wire which is coloured GREEN/YELLOW must be connected to the terminal in 

your plug which is marked with an E or by the earth symbol ( ) or coloured GREEN or 

GREEN /YELLOW.
The wire which is coloured BLUE must be connected to the terminal in your plug which is 

marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal in your plug which 

is marked with the letter L or coloured RED.

If any other plug is used, a 13 amp fuse must be fitted either in the plug or adaptor or at 

the distributor board.

Plug should be BS1363 approved 

Fit a 13 Amp Fuse

Ensure that the outer sheath of the cable 

is firmly held by the clamp

BROWN 

(Live)

13 Amp 

Fuse

BLUE 

(Neutral)

GREEN/YELLOW 

(Earth)

connection to the mains supply

Summary of Contents for vin227





















Reviews: