12
13
TROUBLESHOOTING GUIDE
Problem
Possible Causes
Solutions
No steam is
generated.
1. Water tank is empty.
2. Appliance is not
turned on.
3. Frothing wand is
blocked.
1. Add water to water tank.
2. Turn on the Breville Bijou
Espresso machine and follow the
operating instructions.
3a. Perform the milk frothing wand
clean cycle.
3b. Turn off the unit, ensuring the
wand is cool, unscrew the steam
wand tip and use a needle or
toothpick to unclog the nozzle
opening.
Milk is not foamy
after frothing.
1. Milk is not cold
enough.
2. Milk frothing wand is
too deep in milk.
1. Chill milk prior to steaming.
2. Submerge the milk frothing wand
just below the milk surface.
Espresso:
1. Coffee does
not come out
when brewing
espresso.
2. Coffee comes
out too quickly.
and/or is too
weak.
1a. No water in water
tank.
1b. Espresso grind is too
fine.
1c. Espresso grinds were
tamped with too much
pressure.
1d. Too much espresso in
the filter.
1e. Filter is clogged and
needs to be cleaned.
1f. Appliance is not
turned ON.
2a. Ground coffee is too
coarse.
2b. Not enough coffee in
filter.
1a. Add water to water tank.
1b. Grind coffee to espresso ground
level of fineness.
1c. Tamp (press) the espresso grinds
with less pressure.
1d. Fill the filter with less coffee.
1e. Clean the filter.
1f. Plug the Breville Bijou Espresso
machine into electrical outlet.
2a. Use a finer ground coffee.
2b. Use more coffee.
Cannot brew
coffee immediately
after steaming,
and brew button
indicator light
flashes rapidly.
Unit is over temperature.
1. Ensure you brew your espresso
drinks before steaming milk when
making multiple drinks.
2. Perform cool down cycle as
detailed
The unit has
automatically
switched off.
There is a 25 minute
Auto off function on the
machine.
Press the steam or brew buttons to
reactivate the unit.
REPLACEMENT PARTS
For additional or replacement parts,
please visit
www.breville
-nordic.com
or
call us on
+46 31 3000 500
TROUBLESHOOTING
For troubleshooting and FAQs
visit:
www.brevill
-nordic.com
ELECTRICAL SAFETY
This appliance must be earthed.
If the plug is not suitable for the socket
outlets in your home, it can be removed
and replaced by a plug of the correct type.
If the fuse in a moulded plug needs to be
changed, the fuse cover must be refitted.
The appliance must not be used without
the fuse cover fitted.
If the plug fuse requires replacement, a
fuse of the same rating as that fitted by
the manufacturer must be used. In order
to prevent a hazard do not fit a fuse of a
lower or higher rating.
If the terminals in the plug are not marked
or if you are unsure about the installation
of the plug please contact a qualified
electrician.
Blue
(Neutral)
Brown
(Live)
Green/Yellow
(Earth)
Plug should be ASTA approved to BS1363
Fuse should be ASTA approved to BS1362
Ensure that the outer sheath of
the cable is firmly held by the cord grip
Waste electrical products should not be
disposed of with household waste.
Please recycle where facilities exist. E-
mail us at
for further
recycling and WEEE information.
After sales service & replacement
parts
In the case the appliance does not
operate but is under warranty, return the
product to the place it was purchased for a
replacement. Please be aware that a valid
form of proof of purchase will be required.
For additional support, please contact our
Consumer Service Department at
+46 31
3000 500
or email:
Waste Disposal
