10
CARE AND CLEANING
(CONTINUED)
TROUBLE SHOOTING CHART
•
When the solution has run through the
machine (make sure that all the solution
has run out and there is no pressure in the
machine), turn the selector control to the
“OFF” position.
•
After decalcifying, rinse the water tank
thoroughly and refill with cold tap water.
•
Run the full tank of water though the
water outlet and through the steaming
nozzle (half each).
•
Replace the stainless steel filter and the
machine is ready for use.
9
CARE AND CLEANING
(CONTINUED)
•
After the pressure has been released,
remove the water tank cap and discard
the remaining water (always empty the
water tank between uses).
TO AVOID POSSIBLE BURNS
FROM HOT STEAM AND
WATER, NEVER OPEN THE
WATER TANK CAP WHILE
THERE IS PRESSURE IN THE
WATER TANK. REMOVE ALL
PRESSURE FIRST.
To remove all pressure, proceed
as follows:
1. Switch “OFF” at the power outlet.
2. Place frothing jug under steam wand.
3. Set control to “STEAM” position and allow
steam to escape.
4. Set control to “BREW” position to ensure
pressure is released, then back to the
“OFF” position.
5. Wait for pressure indicator to drop down
before removing cap.
5. The pressure is now removed.
DECALCIFYING
Hard water can cause limestone build up in
and on many of the inner functioning
components, reducing the brewing flow,
power of the machine, and affecting the
quality of coffee.
We advise decalcifying the machine on a
regular basis (once a month) using a liquid
decalcifying agent. Follow the instructions
provided, or use the following as a guide:
Diluted solution (for softer water)
•
1 part decalcifying agent
•
2 parts cold tap water
Concentrated solution
(for harder water)
•
1 part decalcifying agent
•
1 part cold tap water
Decalcifying the machine
•
Make sure the selector control is in the
“OFF” position and that the plug is
disconnected from the power outlet.
•
Make sure the machine is cool and all
pressure in the machine has been
released.
•
Remove the stainless steel filter from the
filter holder and place the filter holder
back in position.
•
Place the empty carafe on the drip tray.
•
Remove the water tank cap and pour in
the decalcifying solution.
•
Screw the water tank cap back on (make
sure the cap is on tight).
•
Plug the machine into the power outlet
and turn the power switch on.
•
Turn the selector switch to the “BREW”
position to ensure pressure is
removed, then turn back to the “OFF”
position. .
•
Let the decalcifying solution run through
the water outlet.
Do not place any of the
components in the
dishwasher.
☛
NOTE!
The stainless steel filters
should not come in contact
with any decalcifying
agents.
Do not use powdered
decalcifying agents.
☛
NOTE!
Problem
Causes
Coffee does not come out
•
Machine was not turned on or plugged in.
through the filter head
•
No water in tank.
•
Selector control not in “BREW” position.
•
Coffee grind is too fine.
•
Too much coffee in the filter.
•
Water tank cap is not secure, steam is escaping.
Coffee comes out too quickly
•
Coffee grind is too coarse.
•
Not enough coffee in filter basket.
Coffee is too weak or watery
•
Coffee grind is not fine enough - use Espresso ground
coffee.
Coffee comes out around the
•
Filter holder is not inserted in the brew head properly.
•
There are coffee grounds around the filter basket rim.
•
There is too much coffee in the filter basket.
•
Coffee has been packed too tightly.
No steam is generated
•
Machine is not turned on.
•
The water tank is empty.
•
There is too much water in the water tank, no room
for steam.
•
Selector control not in “STEAM” position.
Coffee is splattering out of spout
•
The water tank is empty or low (not enough pressure).
Milk is not foamy after frothing
•
Not enough steam.
Fig 9
Press to
release
Press to
release
➞
➞
Pressure
indicator down
BR3578 ESP2 booklet AMENDS 13/1/04 5:46 PM Page 9
