Breezair TBQ Installation Manual Download Page 7 | Manualshive

Page: 7 / 20

Breezair TBQ Installation Manual Download Page 7

TBQ/TBS EVAPORATIVE COOLER INSTALLATION MANUAL

|

7

PREPARING THE DROPPER

The 550 x 550mm / 21.7 x 21.7” dropper duct must have a raw

edge or safe edge at the top. Do not fold in a flange as this may

interfere with the transition and/or weatherdamper.

MOUNTING THE DROPPER

Install the dropper and securely fix it to the roof structure on 3

sides. This may require the addition of extra structural timber.

Important!

The dropper must never sit directly on any ceiling

joists or beams, as this may cause noise or vibration issues,

and possible ceiling damage.
Ensure the top of the dropper is level and square in all directions

(use a spirit level). This helps with levelling the cooler.

The installer must ensure the dropper is suitable, and is secured

adequately for wind conditions at the site. Additional restraints

may be required if the cooler is more than 200mm/8” higher

than the roof timbers, or design wind velocity at the site

exceeds 43m/s / 141fps.
In exposed or very high wind areas use 16 screws, minimum

shank diameter 5.2mm / 7/32” to secure the dropper. In areas

subject to windstorms/hurricanes or where the cooler is located

more than 8m/26’ above the ground seek advice from a

structural engineer.

The dropper may now be flashed to the roof. Make sure there is

no chance of water entering the roof space.

SECURING THE DROPPER & TRANSITION

Fit the transition onto the dropper as shown. Ensure that it

is oriented correctly, as shown by the engraved detail on the

transition.
Check the level of the transition on the dropper, with a spirit

level placed across the flats in both directions.

ILL969-B

Once level, begin securing the transition to the dropper using

the screws provided. There are eight ‘V’ notch locations for

screws.

Only use the screws provided. These must be used in the correct

positions to prevent interference with the weatherdamper. All

eight (8) screws must be used. Check the level periodically

before driving in all the screws.

Ensure the duct insulation is firmly held against the duct

connector flange on the dropper.

ILL967-B

ILL1683-A

ILL1049-B

«
...
5
6
7
8
9
...
»

Summary of Contents for TBQ





















Reviews:

No comments