manualshive.com logo in svg

Brandywine Portable Timing Unit, User Manual, Page: 13 / 31

Share
Download
Brandywine Portable Timing Unit User Manual Download Page 13

 
 

 

MANUAL P/N 900000118 REV D 

13 

 

5.3

 

Viewing the Current Status of the PTU system 

From the “MENU” button, select “General” from the status menu.  This shows 
information such as the current output time, UTC time, up time, the current input 
reference, the current output format, current system state, alarm status, battery 

status, and current internal temperature. 

Figure 4 - PTU Status Page 

Output Time

: The current time of day being displayed or being output by the PTU 

UTC Time

: The current time of day from the GPS constellation in Universal Time 

Coordinate (UTC) 

Up Time

:  The amount of time that the PTU has been powered on 

Hour Meter

:  This is the number of hours since the PTU was first built. 

Reference

: The current reference input being used by the PTU 

Output TimeCode

: The current timecode format in use by the PTU’s outputs 

TFOM

: Time Figure Of Merit – the difference between the unit’s time and the 

reference input.  A 1 means the unit is accurate to within 1ns, a 2 means the unit is 
accurate to within 10ns, a 3 means 100ns, etc 

System state

: The current mode of the PTU’s internal clock 

 

Summary of Contents for Portable Timing Unit
































Reviews:

No comments