manualshive.com logo in svg

Brandywine Portable Timing Unit, User Manual, Page: 10 / 31

Share
Download
Brandywine Portable Timing Unit User Manual Download Page 10

 
 

 

MANUAL P/N 900000118 REV D 

10 

scenario, where the unit has been powered down for longer than 24 hours or has 
been moved more than 60 miles since last use, it may take as long as 15 minutes to 

acquire satellites and start displaying valid time. 
 

A number of GPS parameters can be tracked on the Status page of the web-browser 
interface.  Select the Status tab at the top of the browser.  The number of satellites 
tracked as well as the position data from the GPS can be viewed. 

 
As soon as 4 satellites are tracked, the front panel LED labeled “GPS Locked” will 
light up. 

4.2.3

 

HaveQuick Input 

The HaveQuick reference requires both a standard HaveQuick II and a 1PPS input 
signal, both conforming to ICD-GPS-060A.  Connect the HaveQuick source to J5 and 

the 1PPS source to J9.  Ensure that HaveQuick is selected as reference on the web-
browser Setup page. 

4.2.4

 

IRIG B Input 

Connect a standard 1kHz modulated IRIG-B signal to the BNC connector at J7, and 
ensure that IRIG-B is selected as reference input on the Setup page of the web-

browser. 

4.2.5

 

1PPS 

Connect a standard ICD-GPS-060 1PPS (1 pulse-per-second) signal to the J9 

connector on the rear of the unit and ensure that “Ext 1PPS” is selected as reference 
input on the Setup page of the web-browser. 

 
Enter the date and time manually in the dialog boxes on the same web page and 
click “submit” to allow the PTU to read those values.  

4.2.6

 

Output Timing Signals 

Regardless of the input reference selected, the PTU will always provide the 
following output signals: 

 
 

HaveQuick Out (J4) 

 

Time-code Out (J6). IRIG B125 is the default settings. 

 

1PPS Out (J8) 

4.2.7

 

Front Panel Indications 

The front panel shows a date/time display in years, days, hours, minutes and 
seconds.  The date and time displayed is derived from the currently selected 
reference input, namely GPS, IRIG-B, HaveQuick or 1PPS.  The display is also used to 

display the IP address of the unit on power-up. 
 
The front panel 7-segment time/ date display is turned off by default, to allow the 

maximum battery life during the discharge cycle.  To view the 7-segment display, 
push and hold the “Display” button on the right-hand-side of the front panel. 

Summary of Contents for Portable Timing Unit
































Reviews:

No comments