background image

RECIRCULATION MODE AIR OUTLET 

• 

Insert  the  connection  extension  pieces

laterally in air outlet connection.

• 

Make sure that the outlet of the extension

pieces  is  horizontally  and  vertically

aligned with the chimney outlets.

• 

Connect  the  air  outlet  connection  to  the

hood body outlet using either a flexible or

rigid pipe with 

 150mm.

• 

Ensure  that  the  activated  charcoal  filters

have been inserted.

ELECTRICAL CONNECTION 

• 

The electrical tension must correspond to the tension noted on the label

placed inside the cooker hood.

• 

Connect  the  electrical  plug,  where  provided, to  the  an  easily  accessible

outlet in conformity with local standards in force.

• 

Where  an  electrical  plug  is  not  provided  (for  direct  connection  to

electrical  network)  place  a  standards  approved  bipolar  switch  with  an

aperture distance of not less than 3mm (accessible) from the contacts.

Attention:  substituting  the  supply  cable  must  be  carried  out  by  authorized 

technical assistance service. 

Air outlet 

connection 

12 

SAFETY : Read this First ! 

• 

Do not connect the appliance if there are obvious signs of transportation

damage.

• 

Read  this  user  manual  thoroughly  before  attempting  to  use  this

appliance.

• 

Installation  and  repair  should  be  attempted  only  by  qualified  technical

personnel.

• 

It is dangerous to modify any part of this appliance.

• 

The  manufacturer  declines  all  responsibility  in  case  of  failure  to  adopt

proper safety measures.

• 

Ensure  the  location  in  which  this  appliance  is  installed  has  good,

permanent ventilation.

• 

The  distance  between  the  bench  top  to  the

lower part of the hood must not be at least 75

cm or  higher.

• 

The  exhaust  from  the  canopy  range  hood

must  not  be  discharged  into  any  heating  flue,

which  may  carry  combustion  products  from

other sources.

• 

Do  not  leave  lit  gas  burners  exposed  due  to

risk of fire.

• 

Use  an  electrical  connector  with  earth  that  is

correct for your location.

• 

Check  that  the  voltage  in  your  area  is  correct

before plugging in.

• 

The electrical connection of this appliance must be connected to earth.

Green & yellow 

EARTH 

Blue 

 

NEUTRAL 

Brown   

LIVE 

Summary of Contents for AD995XC









Reviews: