background image

 

 

INSTALLATION INSTRUCTIONS 

 
 
 

AVMS-3604.doc  

Page 2 of 9 

4.

 

Run the camera harness along the under 
hood covering, down the drive side hinge. 
Zip tie the harness to the hinge so the 

harness will not kink or cut. 

5.

 

Run harness into the vehicle though the 

factory grommet in the drivers side firewall. 

6.

 

Route the camera harness to the location of 

the 360º module. 
 

Section 2: 

Side Mirror Camera installation 

1.

 

The inter door panel will have to be 
removed for installation of the side 
cameras. 
 

2.

 

Working on the driver side door. With the 
door closed, place the template sticker 
(

marked LHD

) on the bottom side of the 

mirror with arrow aiming away from the 
vehicle. Perpendicular to the side of the 
body. (

Do not go by mirror lines or angles

.) 

 

3.

 

Make sure the template is to at least the 
middle to outer edge of the mirror. (

The 

camera needs to see only a little of the side 

of the vehicle and mainly the ground and 

objects next to the vehicle

.) 

4.

 

Remove the door panel and the 3 nuts that 
are holding the mirror to the vehicle. 

5.

 

Place the mirror on a soft or padded surface 
and remove the glass from the mirror. 
(

Each vehicle is different, but most are 

mounted by a center circle and will unclip 
from it

.) 

 

 

6.

 

After the glass is removed, check to see if 
where the templates are placed there is 
clearance for the camera and will not cut 
into anything in the mirror housing. (

If the 

template has to be moved make sure to 
keep the arrow aiming the same way

.) 

7.

 

Drill a hole in the bottom of the mirror using 
a hole saw or Uni-bit to the size on the 
template. Which is 1 1/8” 
 

 

 

Summary of Contents for AVMS-3604










Reviews: