manualshive.com logo in svg

Bradley TDB3105, Installation Manual

Share
Download
Bradley TDB3105 Installation Manual Download Page 13

Installation

 TDB3105

Bradley • 215-1563 Rev. E; ECN 12-00-004 

1/15/2013 

13

5

Valve and tubing connections

Flush supply lines before making connections. 
Do not apply pipe sealant to compression fittings.

A

Connect tube from sprayhead to valve 
assembly. The male connector for the valve 
assembly will remain tight and leakproof 
when tubing is cut and installed properly.

B

Using a sharp razor, cut tubing squarely and 
remove any burrs. Do not pinch or crush end 
of tubing.

C

Loosen nut on fitting. Moisten end of tube 
and push into fitting until it is firmly seated. 
Tighten nut to secure tube to fitting (make 
sure nut it securely tightened). If connector 
leaks, reseat tubing according to above 
procedure. If leaking persists call your 
Bradley representative for assistance.

D

Hang valve assembly on pedestal bracket. 
Use screws provided to hang valve on 
bracket.

E

Attach flexible hosing to thermostatic mixing 
valve, two places.

F

Connect hoses to the stop valves. Make sure 
the hot supply is connected to the hot inlet on 
the valve (marked with the letter "H") and the 
cold supply is connected to the cold inlet on 
the valve (marked with the letter "C").

Volume Control

Valve 

Bracket

Flexible 

Hose

Stop 

Valve

Thermostatic Mixing 

Valve Assembly 

(S45-2504)

3/8" Dia. Tube 

from Sprayhead 

(R68-600014)

Tubing

Male Tube 
Connector

Nut

Valve Mounting Bracket

Valve Mounting Screws

Valve Bracket

3/8" Dia. Tube 

from Sprayhead

Summary of Contents for TDB3105























Reviews:

No comments

Brands by name

Popular brands

Load more brands