Bradley HN-400 Installation Instructions Manual Download Page 9

9

Bradley Corporation • 215-781 Rev. D; EN 03-310

Barrier-Free Column Shower

Installation Instructions

HN-400

12-16-2003

Cleaning Instructions 

IMPORTANT:  Cleanliness is of utmost importance. Do not permit salty solutions to

evaporate and dry on stainless steel. Never use ordinary steel wool or
steel brushes on stainless steel. Always use stainless steel wool or
stainless steel brushes.

1. Remove ordinary deposits of dirt and grease with soap and water. Whenever possible, the metal

should be thoroughly rinsed and dried after washing.

2. Use stainless steel polishing powder to get rid of tightly adhering deposits.

3. Look for the source of the rust in some iron or steel not actually a part of the stainless steel struc-

ture. Sometimes the appearance of rust streaks on stainless steel leads to the belief that the stain-
less steel is rusting. A steel nail or screw may be the cause of the trouble. 

4. If the showerhead delivers an uneven spray, remove the showerhead from the unit, disassemble,

and remove foreign matter.

5. Reassemble showerhead and reinstall into unit.

HN-400 Column Shower Warranty

Bradley Corporation warrants to commercial and institutional purchasers only each unit free from defects in
material and workmanship under normal use and service upon the following terms and conditions:

1. This warranty is limited to replacing or repairing, at our option, transportation charges prepaid by the

purchaser, any Bradley unit or part thereof which our inspection shall show to have been defective within
the limitations of this warranty.

2. The period during which Column  Shower components are warranted is one (1) year, measured from the

date of our invoice.

3. This warranty does not cover installation or any other labor charges and does not apply to any units

which have been damaged by accident, abuse, improper installation or improper maintenance.

4. The replacement or repair of defective units as stated in this warranty shall constitute the sole remedy of

the purchaser and the sole liability of Bradley Corporation under this warranty.  Bradley Corporation
shall not otherwise be liable under any circumstances for incidental, consequential or indirect damages
caused by defects in the repair or replacement thereof.

5. This warranty extends only to commercial and institutional purchasers and does not extend to any others,

including consumer customers of commercial and institutional purchasers.

6. This warranty is in lieu of all other warranties, express or implied, including any implied warranty of

merchantability or fitness for a particular purpose or otherwise.  

Summary of Contents for HN-400










Reviews: