background image

IMPORTANT

Read this entire installation manual
to ensure proper installation, then
file these instructions with the
owner or maintenance department. 

Flush all the water supply lines
before making connections. 

Wall anchors used must have a
minimum pull-out rating of 1,000
lbs.

Product warranties may be found
under "Product Information" on our
web site at www.bradleycorp.com.

Table of Contents

Pre-Installation Information  . . . . . . . . . . . . . . . .2
Dimensions  . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4
Installation Instructions  . . . . . . . . . . . . . . . . 5-11
Cleaning and Maintenance  . . . . . . . . . . . . . . . .12
Soap Dispenser Maintenance  . . . . . . . . . . .13-14
Check Valve Troubleshooting . . . . . . . . . . . . . .14
Assembly of Components  . . . . . . . . . . . . . .15-16
Metering Air Valve Maintenance  . . . . . . . . . . .17
Metering Air Valve Troubleshooting . . . . . .17-18
Vernatherm™ Mixing Valve . . . . . . . . . . . . . . .19

P.O. Box 309, Menomonee Falls, WI 53052-0309
TEL. 1-800-BRADLEY

FAX  262-251-5817

http://www.bradleycorp.com

SS-2/AST/STD
SS-2/AST/JUV

Express® Lavatory
System SS-Series

(Standard* and Juvenile Height)

Express® Lavatory Systems
are ADA compliant.

Installation
Instructions
OBSOLETE

215-1244 Rev. D; EN 08-805
© 2008 Bradley Corporation
Page 1 of 19

4/26/08

Summary of Contents for EXPRESS SS-2/AST/JUV




















Reviews: