background image

10

Express® Deck Lavatory System EXD-Series
EXD-2N

Installation Instructions

2/9/07

Bradley Corporation • 215-1542 Rev. E; EN 06-915

Cleaning and Maintenance Instructions

IMPORTANT: Strong alkaline or acid-based chemicals and cleansers should not be

used to clean Terreon®. If these chemicals come in contact with the
Terreon® surface, wipe off the surface immediately and flush with
soapy water.

Terreon® and panel maintenance

The bowl is constructed of Terreon®, a densified solid surface material composed of an acrylic
modified polyester resin. Terreon® is resistant to chemicals, stains, burns and impact. Surface
damage can be easily repaired with everyday cleaners or fine grit abrasives. The panel is made of an
acrylic/ABS laminate, and will not chip, peel or flake. With regular cleaning, your Terreon® fixture
will provide years of dependable service.

Cleaning

• Daily Cleaning:

Wipe the surface with a damp cloth and wipe dry.

• Weekly Cleaning:

Wipe the surface with a damp cloth and a household liquid detergent.

Stubborn stains can be removed as follows:

1. Using a #7448 Scotch-Brite® pad, scrub with an abrasive cleanser such as Ajax®,

Comet® or Soft Scrub® and water.

2. Clean thoroughly with soapy water and allow to dry.

• Scorch Marks:

Although Terreon® will not burn, a lit cigarette in contact with Terreon® could

leave a scorch mark. Scorch marks can be removed by buffing with a #7448 Scotch-Brite pad or
with an abrasive cleaner. 

Repair kit:

In the unlikely event your Terreon® surface becomes damaged, it can easily be

repaired. Contact your Bradley representative to order a repair kit and be sure to specify color
when ordering.

Panel cleaning

IMPORTANT:  Do not use abrasive cleansers to clean the panel. Abrasive cleaners

can mar the surface.

Graffiti/Vandalism:

If vandals create markings on the panel, Bradley recommends using

Motsenbocker’s LIFT OFF® to remove ink and spray paint. Remover #3 is for ink and markers,
and Remover #4 is for spray paint. Motsenbocker’s LIFT OFF® can be ordered through Sanitary
Maintenance Service Inc. (call 1-800-451-5523 x 425 or visit
www.santitarymaintenance.com/product.htm  for ordering information). After cleaning with LIFT
OFF®, give the panel a final thorough cleaning with a liquid tub and tile cleaner to remove soil
and maintain the glossy finish.

NOTE: Use of brand names is intended only to indicate a type of cleaner. This does not constitute an
endorsement, nor does the omission of any brand name cleaner imply its inadequacy. Many products
named are regional in distribution and can be found in local supermarkets, department and hardware
stores or through your cleaning service. It is emphasized that all products should be used in strict
accordance with package instructions.

Summary of Contents for EXD-2N














Reviews: