background image

2

   Unpacking

Models

Type

Electrical Input

Rated Amperage

Rated Watts

Certifications

2922-287300 

2922-287400

Automatic

120VAC, 50/ 60Hz

10A

1200

   Description

Warm air hand dryer, powered by a universal brush motor, delivers up to 800 watts of drying power and incorporates an 

integrated element for heated air.  The dryer controls provide for (3) distinct levels of motor operation (Hi, Med and Low) 

and the option of operation with, or without, the heating element.  An infrared sensor is used to automatically activate the 

dryer.  These models are intended for use in commercial, industrial, office and public facility environments.  

   Electrical Specifications

Table 1

  

 
   General Safety Information

       DANGER 

  Failure to disconnect the power source before installation or servicing can result in serious 

injury or death from electric shock. 

•  Always disconnect the power source before servicing or installing the hand dryer.

       DANGER  

 Failure to properly ground this unit could result in severe electrical shock and/or death. 

•  This hand dryer must be properly grounded (Earthed) for safe operation. An identified ground connection point is 

supplied on the hand dryer’s wall base.

•  We recommend GFCI protection in wet or damp locations or as required by local code.

       WARNING   

Risk of fire, personal injury or property damage are possible if local codes, or safety 

recommendations are not followed. 

•  Installation and servicing should only be performed by qualified electrical technicians. 

•  Use only the electrical power (voltage and frequency) specified for the model hand dryer being installed. See Table 1  - 

Electrical Specifications.

•  Connect the hand dryer to the nearest suitable distribution panel.

•  To limit a voltage drop, and insure efficient operation, use No. 12 AWG (4 mm2) wire or larger as required by local 

electrical codes.

•  Always connect to a branch circuit with circuit breaker or fuse protection with an electrical rating greater than the model 

hand dryer’s rated amperage shown in Table 1 - Electrical Specifications in accordance with the NEC (National Electrical 

Code) and/or CEC (Canadian Electrical Code).

•  To avoid a hazard due to inadvertent resetting of the thermal cutout, the hand dryer must not be supplied through an 

external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.

•  Each automatic model hand dryer must have a dedicated circuit.

•  Route all field wiring away from moving parts within the hand dryer.

       CAUTION   

 Improper mounting could result in personal injury or property damage.

•  Follow the mounting height recommendations in Table 2.

•  On a stud wall, one side of the hand dryer should be mounted to an existing stud.

1.   Remove all packing material. Recycling is recommended.

2.   Carefully remove the hand dryer from the shipping carton, using care not to drop the appliance.

3.   Inspect carefully for any damage that may have occurred during transit. Check for any loose, missing or damaged 

parts. If the hand dryer is damaged, promptly inform the dealer where you purchased it.

07/12/17

Bradley P20-200 Rev. B; ECN 17-15-021

Summary of Contents for 2922-287300

















Reviews: