A.
Cover.
B.
User manual´s poquet.
C.
Ergo seat cushion for group 0
D.
Harness pads.
E.
Harness straps.
F.
Buckle release-button.
G.
Locking buckle.
H.
Harness adjustment button.
I.
Harness adjuster strap.
J.
Child seat gradient adjuster.
K.
Metal lever for angle adjustment Group 0.
L.
Button for fastening seat cover.
M.
Group 0 belt hook.
N.
Locking clip.
O.
Group 0 and 1 belt hook.
P.
Harness strap slot.
Q.
Harness pad connector.
R.
Group 1 belt hook.
S.
Metal harness connector.
2. SEAT PARTS AND FITTINGS
3. INSTALLING CHILD SEAT. GROUP 0.
Only suitable for
Group 0
, approx.
0 to 9 months (0-10 Kg.)
WARNIG
1.
Recline the seat as posible. To adjust the reclining
position of the child seat, pull the red handle
J
forward until you reach the required position (3.1).
2.
Pull the metal lever
K
at the front of the base and
pull upwards releasing the lever when the stop is
reached (3.2).
3.
Install the child seat rearward facing (3.3).
4.
Fasten the child seat by thread the lap bel and the
diagonal belt throught the belt guide slot.Thread the
diagonal belt throught the
O
slot with blue arrow on
the back, and thread the lap belt throught the slot
M
with blue arrow on the base (3.4, 3.5, 3.6 y 3.7).
Do not use the child seat on a passenger seat fitted
with an active airbag.
IMPORTANT
Ensure that the belt has no slack.
5.
Fasten the seat belt into the vehicle´s buckle until
it “
clicks”
, making sure the child seat is properly
installed.
6.
Tighten the lap belt and diagonal shoulder belt,
then place the red safety clip
N
on the diagonal
shoulder belt tongue as near to the vehicle anchor
point as possible without touching it! (3.4, 3.8, 3.9
y 3.10).
Make sure the vehicle’s safety belt is not twisted,
also check that the seat cover does not impede the
movement of the vehicle’s safety belt or prevent the
installation of the seat in any way. To release your
child unbuckle the vehicle safety belt as described
in the instructions.
4. INSTALLING CHILD SEAT. GROUP 1.
Only suitable for
Group 1
, approx.
9 months to 4 years of age (9-18 Kg.)
WARNING
Installing the child seat forward facing can only be
maid if the child is more than 9 kg.
1.
To install a Group 1 seat, you must first remove the
padding for Group 0.
2.
Pull the metal lever
K
at the front of the base and
pull upwards releasing the lever when the stop is
reached (4.1).
3.
The seat must be in its most upright position to
adjust reclining angle of the child seat, pull the
control red handle
J
towards you until the desired
position is achieved (4.2).
4.
Fit this child seat into the vehicle´s seat, making
sure it is firmly pressed against the vehicle seat
backrest (4.3).
26
BM01
Child restraint system
27
www.babyqs.com
Group 0/1
EN
Summary of Contents for BM01
