en 3
2
5
6
8
7
3
4
The device is intended for the opening and closing of garage doors
(please refer to section 6 “Door Types”). The device is not meant for commer-
cial use but solely for the use in private garage doors that are appropriate for
a single household. Any improper use of the drive could increase the risk of
accidents. The manufacturer assumes no liability for such usage. Only the
ori-
ginal
accessories may be connected to the drive. With this drive, automated
gates must comply with the currently valid international and country-specific
standards, guidelines and regulations (among other things, EN 13241, EN
12453 and EN 12604).
IMPORTANT NOTE
If your garage does not have a side entrance, an external emergency
release should be installed. This allows for manual operation of the
garage door from the outside during power failure.
Ladder
Marking pen
Pliers
Drilling machine
Hammer
Ratchet 10 mm / 13 mm
Hacksaw
Different drill bits for concrete
and(or wood (8, 6, 5, 4.5 mm)
Box wrench
Water level
Screwdriver
Measuring tape
First, check whether your door is balanced and in equilibrium.
Open your door about halfway and let it go.
The door can now hardly change its position
independently
,
but must remain in this position held by the spring force alone.
1.
The rail of the garage door MUST be connected securely and firm
-
ly to the supporting wall or ceiling above the garage door.
2.
Additional brackets and mounting rails (not included in the supply)
might be required, if the your garage ceiling has a cladding, boards
or similar.
3.
If your garage does not have a separate side entrance, an external
emergency release (refer to section “Optional Accessories”) must
be installed.
A. One-Piece Door with Horizontal Track Only.
B. One-Piece Door with Horizontal and Vertical Track – Canopy door
arm and photo cells required. See your dealer.
C. Sectional Door with Curved Track – connect door arm.
D. Canopy door arm and photo cells required. See your dealer.
E. Canopy door arm for use on door types B and D.
Note:
The system BPA500 cannot be used for one-piece garage doors
with horizontal and vertical guide rails and two-wing doors.
Please check the supplied parts for completeness before starting the in-
stallation. Note: The numbering only applies to the corresponding section.
This figure always offers you a complete overview of the readyassem
-
bled system during the step by step installation of the system.
Intended use
Before you begin
Door Types
Tools required
Preparation
Scope of supply
Product overview
Parts overview:
Tool list:
Hardwarebag:
a. Header bracket
h.
Power cable
b. Belt
i.
Drive head
c. Rail
j.
Release
d. Carriage
k.
Straight door arm
e. Connecting piece
l.
Curved door arm
f.
Rail bracket
m.
Door bracket
g. Hanging bracket
1. Drive head
1x
8.
Curved door arm 45° *
1x
2. Remote control
2x
9.
Curved door arm 90° (BPA1200) 1x
3. Rail bracket
2
x
10. C-bracket *
2x
4. Hardwarebag
1x
11. Hanging bracket
2x
5. Header bracket *
1x
12. Wireless Wall Control
(BPA650-1200)
1x
6. Door bracket
1x
13. Rail 8323CR5 (BPA500)
1x
7. Adapter for gear wheel *
1x
* Delivery with the rail
14. Truss head screw
6 x 80 mm
1x
19. Safety cotter pin
1x
15. Lock nut M6
1x
20. Screw ST 6,3 x 50 mm
6x
16. Hexagonal head screw 6x
21. Screw ST 6,3 x 18 mm
8x
17. Nut M6
6x
22. Plug
6x
18. Bolt
1x
